07-09-2015, 12:07 AM
07-09-2015, 08:22 AM
this is the number that I used to order the gear with the last time I ordered one
P9249303
can't say that they will have one, the last time I tried to order one they were backordered and 8 months later when the canoe came in they wanted like 80 dollars for it, so I choked up and made one because I just happened to have an involute gear cutter that matched the pitch of the one I needed.
P9249303
can't say that they will have one, the last time I tried to order one they were backordered and 8 months later when the canoe came in they wanted like 80 dollars for it, so I choked up and made one because I just happened to have an involute gear cutter that matched the pitch of the one I needed.
07-09-2015, 08:43 PM
Thanks dallen. What is the model of lathe at grizzly that the number pertains too?
Mark
Mark
07-09-2015, 08:57 PM
the part number is off of a 12X36 belt driven lathe, but I haven't been able to track down the manual that I found the number in.
you should be able to call Grizzly and give them that number and find out if they have a gear in stock.
you should be able to call Grizzly and give them that number and find out if they have a gear in stock.
07-10-2015, 05:44 AM
These links might help.
https://www.grizzly.com/parts/P9249303
https://www.grizzly.com/products/g9249/parts
Ed
https://www.grizzly.com/parts/P9249303
https://www.grizzly.com/products/g9249/parts
Ed
07-10-2015, 06:49 AM
Those are very helpful links Ed. Maybe I'm looking at that picture wrong but I think the gear in the picture Mark posted that is worn out is number 335 in the diagram, not the worm gear number 303. However, since those 2 gears are in mesh I think I would replace them both.
07-10-2015, 09:57 AM
Well, I guess we will find out if they are the right parts, I ordered the worm and helical as John suggested from Ed's link. The parts look identical. (crossing fingers)
The worm gear is 15usd, but the helical brass mating gear is 68usd, so it is fairly expensive. But what can you do? Probably most folks don't have the tooling to cut that gear.
Mark
The worm gear is 15usd, but the helical brass mating gear is 68usd, so it is fairly expensive. But what can you do? Probably most folks don't have the tooling to cut that gear.
Mark
07-10-2015, 05:31 PM
Mark, I was thinking about looking up part numbers in my manual for my Busy Bee 12 x 36 but, with the help I've had from Busy Bee
parts wise I didn't venture any suggestions about contacting them.
I'll be following this thread to see how you make out.
Steve
parts wise I didn't venture any suggestions about contacting them.
I'll be following this thread to see how you make out.
Steve
07-12-2015, 03:23 PM
I got some more work done on the lathe this weekend. Mainly the threading box and some shafts. Three new ball bearings will be needed.
I also did some measurements for the cross slide leadscrew, and found an issue I wanted to correct with the help of Edk (blueprints) and PixMan (leadscrew machining). The exploded view (courtesy of Johnnyc14) shows the position of the feedgear to be teeth toward thrust bearing:
Which gives a mesh like this:
(this view is looking up through the apron to the topmost gear)
If the gear is in the position I received it in, the mesh is like this:
Which isn't that bad except that the gear shoulder contacts about .030" of the thrust bearing:
So, I think I will put a spacer here:
And reverse the gear to match the exploded view position. Also move the position of the new leadscrew shoulder to back up the drive gear, so the only force going through the roll pin will be turning, instead of push/pull and turning. I guess its back to the garage for me...
I also did some measurements for the cross slide leadscrew, and found an issue I wanted to correct with the help of Edk (blueprints) and PixMan (leadscrew machining). The exploded view (courtesy of Johnnyc14) shows the position of the feedgear to be teeth toward thrust bearing:
Which gives a mesh like this:
(this view is looking up through the apron to the topmost gear)
If the gear is in the position I received it in, the mesh is like this:
Which isn't that bad except that the gear shoulder contacts about .030" of the thrust bearing:
So, I think I will put a spacer here:
And reverse the gear to match the exploded view position. Also move the position of the new leadscrew shoulder to back up the drive gear, so the only force going through the roll pin will be turning, instead of push/pull and turning. I guess its back to the garage for me...
07-12-2015, 04:22 PM