MetalworkingFun Forum

Full Version: Tramming Post Style Mill/Drill
You're currently viewing a stripped down version of our content. View the full version with proper formatting.
Pages: 1 2
I have a Post Style milling machine. I got the unit set up a few weeks ago, but haven't used it yet. Today I decided to install my milling vise. I'm finding it very hard to get the fixed jaw on the vise set true to the quill. I keep getting different readings across the 5.25" vise jaw.
Is there a easy way to tram a Post Style Mill?
Let's get some terms straight here first; "tramming" normally refers to the process of setting the quill on a mill perpendicular to the table. If you are trying to get the solid jaw on the vise parallel to the X feed on the table, you are "indicating" it. To do that, you need slightly loosen the hold down bolts, sweep an indicator across the solid jaw by moving the table and adjust its alignment before re-tightening the bolts. There is a quick video on my YouTube site that shows a really quick way to do it.

How to Indicate the Vise on a Milling Machine in Just One Pass


Tom
(11-05-2017, 08:40 AM)TomG Wrote: [ -> ]Let's get some terms straight here first; "tramming" normally refers to the process of setting the quill on a mill perpendicular to the table. If you are trying to get the solid jaw on the vise parallel to the X feed on the table, you are "indicating" it. To do that, you need slightly loosen the hold down bolts, sweep an indicator across the solid jaw by moving the table and adjust its alignment before re-tightening the bolts. There is a quick video on my YouTube site that shows a really quick way to do it.

How to Indicate the Vise on a Milling Machine in Just One Pass


Tom

Tom.
Thanks for correcting me on the terms. I wasn't sure if I was right on that or not. 
Since the head of mine is on a round post and can swivel from side to side. How do it know it's sitting perfectly centered or at zero degrees to the table? There is no degree indicator or mark on either the head or the post. 
Should I indicate the quill to a T Slot in the table before trying to indicate the Vise?
Thanks Trevor
This is my Mill/Drill

[attachment=15220]

I got thinking last night that maybe I should set the head at the height I require it to be on the post. 
Then indicate the head to the table and lock it down first. Then try to indicate the Vise. 
Am I right in thinking that way? Just worry about one setting at a time!
The table moves relative to the position of the spindle, so its position doesn't matter. Off hand, I can't think of any reason to accurately set the head perpendicular to the table. I know in the 45 years or so that I've been doing this stuff, I never have. Big Grin

It would be nearly impossible to do on your machine anyway because there is no over arm to move the head.

Tom
May be a stupid question.
But what is a over arm?
(11-05-2017, 09:18 AM)Cross Slide Wrote: [ -> ]May be a stupid question.
But what is a over arm?

Not a stupid question at all.

See the image below. The overarm (ram) allows you to move the head forward and backwards.

Ed

[attachment=15221]
(11-05-2017, 09:45 AM)EdK Wrote: [ -> ]
(11-05-2017, 09:18 AM)Cross Slide Wrote: [ -> ]May be a stupid question.
But what is a over arm?

Not a stupid question at all.

See the image below. The overarm (ram) allows you to move the head forward and backwards.

Ed

Thanks Ed. 
That definatly clears that question up. 

I'm starting to think my test indicator is not accurate. 
I have tried Toms method and it's still reading out of alignment.
(11-04-2017, 10:09 PM)Cross Slide Wrote: [ -> ]I'm finding it very hard to get the fixed jaw on the vise set true to the quill. I keep getting different readings across the 5.25" vise jaw.
Is there a easy way to tram a Post Style Mill?

All you need to concern yourself with is getting the left side of the vice jaw to read the same as the right side of the vice jaw. If your indicator varies a little bit going across the center portion of the jaw that is not unusual. Vice jaws are not all 100% flat. You just don't want a steady increase or decrease in your reading from one side to the other.

The only time that "swiveling" the head of the mill would be a concern is if you change the height of the head between operations on the same part. For example if you drill a hole in a piece of material, and then find you don't have enough space to insert a reamer to finish the hole. So you raise the head of the mill to install the longer reamer. If the head pivots slightly while raising the head (and you don't notice it) you are no longer in line with the hole you started. If you are lucky and catch it, you would need to re-locate the center of your hole again.

Like Tom sez - it doesn't really matter which way the head is pointing as long as you can reach every point of your material you need to get to.

Smiley-gen163
Is your indicator sticking? Try moving it with a finger and make sure it's free throughout its travel.

Tom
Pages: 1 2