05-30-2012, 01:53 PM
05-30-2012, 03:45 PM
Unal,
Very nice
I like the micro boring tool
That is why we should keep broken & blunt cutting tools (i have loads)
John
Very nice
I like the micro boring tool
That is why we should keep broken & blunt cutting tools (i have loads)
John
ukazak
05-30-2012, 04:50 PM
Thanks Dave, John,
So, Dave, as you calculated, 0.05 to 0.10mm was good for press fitting allowance for, this mating, Brass and stainless...
Yes, John, we keep keeping the old stuff, thinking that someday might come of need,.. all end up with boxes of things, piling on us, shop looks like a junk yard. tried many attempts to clean out, but end up sorting the stuff, never beared to throw away.
Now, I have to fix close fitting Crank disk pins. they are little too lose to my like(ing). both hole and the pins are exact 3mm dia. but they are just lose... when the rots connected, it will not stay on for long.
unal
So, Dave, as you calculated, 0.05 to 0.10mm was good for press fitting allowance for, this mating, Brass and stainless...
Yes, John, we keep keeping the old stuff, thinking that someday might come of need,.. all end up with boxes of things, piling on us, shop looks like a junk yard. tried many attempts to clean out, but end up sorting the stuff, never beared to throw away.
Now, I have to fix close fitting Crank disk pins. they are little too lose to my like(ing). both hole and the pins are exact 3mm dia. but they are just lose... when the rots connected, it will not stay on for long.
unal
05-30-2012, 06:42 PM
(05-30-2012, 04:50 PM)ukazak Wrote: [ -> ]Thanks Dave, John,
So, Dave, as you calculated, 0.05 to 0.10mm was good for press fitting allowance for, this mating, Brass and stainless...
Yes, John, we keep keeping the old stuff, thinking that someday might come of need,.. all end up with boxes of things, piling on us, shop looks like a junk yard. tried many attempts to clean out, but end up sorting the stuff, never beared to throw away.
Now, I have to fix close fitting Crank disk pins. they are little too lose to my like(ing). both hole and the pins are exact 3mm dia. but they are just lose... when the rots connected, it will not stay on for long.
unal
Your crank project is looking very nice and job well done on the re-purposed drill bit. I'll remember that one.
You just described my shop, basement, and garage to a "T". About every few months (year or two, who keeps track?) I resort to going through my "pile" looking for something that I can use in my son's science project or to fix something around the house. Without fail, once I've found such a piece I give a triumphant cry to my wife, "See! This is why I never throw anything out!" Also, without fail, she gives me that "look" and rolls her eyes.
-Ron
05-31-2012, 05:53 AM
Good job Unal, I'm really amazed you can work to that level of precision with a digital caliper, I NEVER get the same readings with mine as I do with a micrometer.
Ron, "Without fail, once I've found such a piece I give a triumphant cry to my wife, "See! This is why I never throw anything out!" Also, without fail, she gives me that "look" and rolls her eyes."
I'm sure I have said those very same words with the identical response.
Ron, "Without fail, once I've found such a piece I give a triumphant cry to my wife, "See! This is why I never throw anything out!" Also, without fail, she gives me that "look" and rolls her eyes."
I'm sure I have said those very same words with the identical response.
ukazak
05-31-2012, 12:43 PM
(05-31-2012, 05:53 AM)stevec Wrote: [ -> ]Good job Unal, I'm really amazed you can work to that level of precision with a digital caliper, I NEVER get the same readings with mine as I do with a micrometer.
Ron, "Without fail, once I've found such a piece I give a triumphant cry to my wife, "See! This is why I never throw anything out!" Also, without fail, she gives me that "look" and rolls her eyes."
I'm sure I have said those very same words with the identical response.
ask me how many times stopped and check it. It is amezing I use the dials on the machine and it works.. but check it again anyways, when I start trusting thye dials, than will be real fun.
you are luck all you get is "look"... sometimes, I see mine coming out of the shop with a largest hammer in one hand, and smalest screwdriver on the other, she sys she will fix that washing machines stucked lid, and than I get that "look" you talk about.
unal
ukazak
05-31-2012, 12:46 PM
(05-30-2012, 01:53 PM)DaveH Wrote: [ -> ]Unal,
Very nicely done, and a very and they look good as well
DaveH
Yea! you sat that, but we gets no banana..!
05-31-2012, 12:55 PM
(05-31-2012, 12:46 PM)ukazak Wrote: [ -> ]Yea! you sat that, but we gets no banana..!
Yeah- you do the "self satisfaction banana"
DaveH
05-31-2012, 06:20 PM
(05-31-2012, 12:43 PM)ukazak Wrote: [ -> ]ask me how many times stopped and check it. It is amezing I use the dials on the machine and it works.. but check it again anyways, when I start trusting thye dials, than will be real fun.Sorry unal, I don't understand
unal
Steve
05-31-2012, 10:07 PM
nice work unal