MetalworkingFun Forum

Full Version: Todays Project - What did you do today?
You're currently viewing a stripped down version of our content. View the full version with proper formatting.
Pages: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 500 501 502 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549
(04-28-2014, 02:35 PM)awemawson Wrote: [ -> ]Decided to do a bit of routine maintenance on my tractor..

Ferguson?
(04-28-2014, 02:35 PM)awemawson Wrote: [ -> ]I knew the main shaft bearings were on the way out,
From the pics, seems a little understated Rotfl Rotfl Rotfl
Smiley-eatdrink004
DaveH
Ford 4000 1974
(04-28-2014, 02:41 PM)DaveH Wrote: [ -> ]
(04-28-2014, 02:35 PM)awemawson Wrote: [ -> ]I knew the main shaft bearings were on the way out,
From the pics, seems a little understated Rotfl Rotfl Rotfl
Smiley-eatdrink004
DaveH

Well you know that Englishmen are modest :)
I actually started making these brake pad retainer pins for Neil on Friday, but hit a roadblock. Rare for me.

They are made out of a Ø 0.870" valve actuator shaft that's some form of 1704PH (precipitation hardening) stainless steel. While turning the long 0.184" diameter, I noticed right away that this stuff would work-harden in a flash, and it gave me fits. Neil had finished the 0.184" diameter on one while I ran an errand, and warned me that he was having trouble with it work-hardening. He was right. My carbide inserts weren't holding up all that well, so I switched to some cermet TPG inserts and got through it.

[Image: IMG_2282-r_zpsd0efbc5f.jpg]

To turn the length of 2.125 without a center, the trick was to turn about .400" (10mm) of length at a time to finish size and then move further down the length another .400". That worked well. Neil had said we didn't need to mill the hex like the original, because it's something that just pull straight out and doesn't require turning with a wrench. I simply put a freehand form on them and polished, that's why they're on an exact match. However, the 1.5mm (0.0591") hole has to be there, and that was my undoing.

The parts were held in a 3/16" 5C collet and square collet block, faster to set up and use than my spindexer. I spotted the holes both sides with a 1/8" (3.18mm) 118º spot drill and set to drilling the holes with a new 1.5mm HSS-Co drill I had. And the second one. They dulled almost instantly, as did both No.53 drills I had. I found I had one 1/16" solid carbide twist drill with 1/8" shank. It drilled one hole and broke the second it drilled through the part. I was able to punch the broken tip out of the hole, but was now at a loss for drilling the second part. Here's the mass of dulled and broken drills it tool to drill but two 1.5mm holes through about 0.150" of material. The one in the lower right is one of the two Titex A1164TIN-1.5 solid carbide TiN-coated drills I'd ordered Monday morning.

[Image: IMG_2281-r_zps47122898.jpg]

As I went to pick up the drills from my distributor, it occurred to me the most of the reason that the one carbide drill I'd tried and broken had failed because the quill on my machine gets a bit stiff at the end of its 5" travel. I had little feel for how the tool was cutting and it grabbed and broke as it cut through the part into the opposite side's 118º spot. Stupid me, I have a nearly new, unused by me Albrecht No.1 drill chuck with sensitive drilling mount!

I set that in the machine and drilled the second hole successfully! Here's the drill I used:

[Image: IMG_2283-r_zps23e82f2f.jpg]

Glad it got done! Neil will be picking up the pins tomorrow, and I can move on to Ed's lathe cross slide parts and let Neil make the handlebar end weights he needs.
Nice work Ken. I don't feel so bad about dulling those 3/8" drills now. I bet you are glad that Ed's and my parts are not made out of exotic materials Big Grin
I'm glad I'm not the only one that has an occasional bad day in the shop.

Ed
Back in the cabinet shop building cupboards I had planned to do over the winter. This set is black cherry with birch plywood carcasses.

[Image: IMG_1131.jpg]

[Image: IMG_1136.jpg]

Door parts

[Image: IMG_1135.jpg]
nice cupboards, I was up to my elbows in a computer case most of the afternoon, controls for the router I put together

[Image: computer3.jpg]
Thats pretty neat, are the drivers for the steppers and breakout board mounted inside the case of the computer running it?
Pages: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 500 501 502 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549