MetalworkingFun Forum

Full Version: Todays Project - What did you do today?
You're currently viewing a stripped down version of our content. View the full version with proper formatting.
Pages: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 500 501 502 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549
Penguin,
Looks to me like a DYMO labeler is in your future...

http://www.officedepot.com/a/products/35...bel-Maker/
I have to go to a job in the morning, to change out 3 VFDs, to a different model/brand and control package. After that I have to drive to a job for the gov't.

The existing VFDs are Allen-Bradley, inverter type 3-5 hp VFDs, to be replaced by ABB brand VFDs, with selectable, 1-5 VDC, 1-10VDC or 4-20ma, control signals and a NEMA 12 enclosure. I hoping to keep the A-B VFDs, they are selectable for 230 vac 3 phase in/230 vac 3 phase out, to run a 5 hp motor, or 240 vac single phase in/230 vac 3 phase out to run up to a 3 hp motor. Just what I need in the shop for the 2 mills and the lathe.

The job for the gov't, is a boiler start up in an arsenal for the US Army. Not my idea of fun or enjoyment, but has to be up and running by 4/1/16. Wish me luck.

Last week the odometer on 2013 service van rolled over 90,000 miles. I use to be a boiler service technician, who drove to the jobsite to work, now I seem to be more of a truck driver, who occasionally fixes boilers.
__________________
(03-16-2016, 12:47 PM)the penguin Wrote: [ -> ]So far I spent the majority of the day in the shop, cleaning and sorting. I had a quick job to do, so I spent almost all of the last 3 hours looking for a 1/8" carbide end mill. I finally found them, in the first drawer I looked in and multiple times afterwards. I thought they were 1/4" carbide end mills, I either need new glasses or learn how to read......................DAMN!!

I did find a few items, I was looking for, the odd nut and bolt, and other hardware, the 1/8" carbide end mills are a the red arrow

Damn Jack, you keep that up you will not reconize the place. Smile
(03-16-2016, 06:50 PM)the penguin Wrote: [ -> ]I hoping to keep the A-B VFDs, they are selectable for 230 vac 3 phase in/230 vac 3 phase out, to run a 5 hp motor, or 240 vac single phase in/230 vac 3 phase out to run up to a 3 hp motor. Just what I need in the shop for the 2 mills and the lathe.

You'd definitely earn a few You Suck s if you scored those VFDs. Happyyes

Ed
(03-16-2016, 06:50 PM)the penguin Wrote: [ -> ]...The job for the gov't, is a boiler start up in an arsenal for the US Army. Not my idea of fun or enjoyment, but has to be up and running by 4/1/16. Wish me luck...
__________________

I'm glad to see that the government has a sense of humor when it comes to setting project deadlines Big Grin
(03-12-2016, 02:59 PM)the penguin Wrote: [ -> ]I've spent the majority of the day, so far in the continuing quest to get better lighting in the shop.  So far about half of the light have gone from florescent and incandescent to LED. As the shop is a black hole, where light goes to disappear, it seems to be brighter and a better quality of light.

What is the fininsh on the walls and ceiling ?

White paint reflects 85%.
My shop walls are white and there are cobwebs with chips dangling and oil splatters making a mess. And it's still dark; there's a flashlight in my toolbox. I'd prefer the ambiance of natural wood walls and a white ceiling - white does help. To each his own as my shop is NOT lab-like at all. What a hoot that would be! <grin>

Okay. I corrected my brainfarted gearbox. A half-thou off, not bad for a 100 year old mill (not the one in the picture, that's a mill/drill for photo ops). Smile
Finally finished up installing the DRO on my lathe. As usual it was another project that didn't go exactly as planned but I survived it anyway. It began with the arrival of the package being covered in shoe prints from end to end, as if someone had been using it for a diving board at their pool. The shipping box contained all of the component parts in their own separate boxes, that were thrown loosely into the larger shipping box. Everything looked like it was OK however.

I started by locating the 5 holes needed in the back of the lathe bed to mount the backing spar that holds the Z axis scale. Drilled and tapped the first hole at the head stock end of the bed and attached the spar with a bolt. Leveled the back end of the spar (parallel to the saddle travel) and drilled and tapped the second hole at the tail stock end. Checking the full length of the spar showed that it was bowed down in the center slightly. (Remember those foot prints on the box?)   Bash

I used a couple of machinist jacks in the center of the spar to get it straight again and drilled and tapped the final 3 holes in the middle. Since the side of bed casting isn't a machined surface I need to use the supplied leveling blocks behind the spar to make sure it was sitting plumb and parallel to the ways. I was slipping the leveling blocks onto each bolt when I discovered I only had 4 of them in the box - not 5. It's always something...   Bash

I searched every box multiple times and didn't find one. I started looking at the paperwork that shows all the hardware that is supposed to be supplied and see FOUR blocks listed. What the ...?   17428
Digging further into the paperwork, I started looking at part numbers and discovered ENCO sent me the wrong backing spar! Instead of sending me the proper 36" spar (that has 4 holes in it) they sent me a 42" spar (with 5 holes in it) and then hack-sawed the ends off of it to make it 36" long!

Seeing as I have already drilled and tapped the 5 holes in my lathe, I thought OK no big deal - I'll just call ENCO and have them send me one more leveling block.  WRONG!

Once again the only thing the MORONS at ENCO were willing to do, was to let me return the entire DRO package for a refund. They wouldn't pull a leveling block out of another box to send to me. They wouldn't contact the manufacturer and have them send me another block either. "You will have to do that yourself." I said that's funny because you certainly didn't have any problem pulling the wrong spar from another box and sawing it off before sending it to me!!!   Rant

So "I" ended up calling Acu-rite myself and spoke to "Kevin" in the tech dept and explained my situation. He says... "Well, you'll have to contact Enco and...."

I stopped him and told him I just got off of the phone with Enco, and what they wanted me to do. "Oh, HELL NO!" he says.   Big Grin  Another leveling block arrived 2 days later - no charge.   Smiley-eatdrink004

I got everything back together and was setting up the display. As I was trying it out I thought something isn't right with the X axis reading. The scales have the same resolution as the scales on my mill (.0002") and the mill has always been spot on. The Z scale on the lathe seemed to be working just fine, but I couldn't get a .0002 reading on the cross slide (X scale). It acted like it was skipping counts and would only display .0004" changes.  17428

So I was thinking great, now I've got a bad scale too. That was late last night and I decide to sleep on it. This morning I tried going through the troubleshooting section in the manual, and it basically says if you have a bad scale it has to be replaced - they don't "repair" scales. And then I had a thought. I went back to the lathe and toggled the X display from "diameter" to "radius" and BINGO! There is nothing in the manual about this, and I've never used a lathe DRO before but it kind of made sense that the resolution might double along with the "diameter" display choice. So I'm assuming all is good.   Blush

[attachment=13094]
Finished up a cart for my new plasma cutter.  Was concerned it would be too top heavy, but its quite stable.

[Image: fd3be196-cd96-45f0-a054-542731d60de7_zpsdpor4jq5.jpg]

[/url][url=http://s1016.photobucket.com/user/drstan/media/DSCN1544_zps6n3aoumk.jpg.html][Image: DSCN1544_zps6n3aoumk.jpg]

BTW, used dumpster tubing, old wheels probably from a lawnmower, a couple of re-purposed swivel casters, a left over piece of rebar, and some surplus nuts & bolts.
Looks good. Prolly something I need to do, but for now it's easier to just pick it up and carry it where I need it.
Pages: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 500 501 502 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549