MetalworkingFun Forum

Pages: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 500 501 502 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549 550

Oooooh, I like it. Thumbsup

What Ed said!

Thanks guys, No prints Stan, it was another that looks about right and how long its that piece designs.

(07-21-2017, 06:42 AM)f350ca Wrote: [ -> ]Thanks guys, No prints Stan, it was another that looks about right and how long its that piece designs.

So somewhere between a WAG & a SWAG? Thumbsup

Well at least there's a very good pic. Need to acquire some cast iron.

A story on the cast iron. I found two chunks of it imbedded in the concrete floor of an old plywood plant, The veneer dryer sat on these. They were about 8x8x2 with a hole in the middle slotted out to the one side. Originally thought they were steel, till I tried welding to one. The weld didn't hold. Assumed it would be hard as glass and full of porosity. Turns out its the nicest to machine cast I've ran across with a nice fine grain. Guess you never know what your going to find.

No projects going on so your going to get wood again.
The base for a table Im building. Actually had to buy the 2 inch lumber, thought I had sawn some but guess not.
[Image: SZGwQSh_cLGQDhJLWpN-ARb-sBWjafba540T5Rld...2-h1276-no]

[Image: SZGwQSh_cLGQDhJLWpN-ARb-sBWjafba540T5Rld...2-h1276-no]

Greg,

Is that ash? It's kind of hard to tell from the picture. I thought maple at first but the grain doesn't quite look like maple. Chin

The camera on my some what dumb phone isn't very good Ed, combine that with my photographic skills and I can make Ash look like Maple. Yes its Ash, been having a run on it lately, may have to put incentives on Butternut to use up some of that inventory.

Just got back from a tour of the local hydro plant. Its been operating for 100 years. Still using the original generators and switch gear. Noticed on the one generator makers plate, made by General Electric in Toronto, that it had been rewound in 1938.

http://www.opg.com/generating-power/hydr...ation.aspx

Just to make it a portable project on a metal forum.

[Image: wwYPjENosow7-1nzEKD7s3NIKGo-1nDrkxm0JML0...2-h1276-no]

Mike E.

Mayhem

f350ca

Dr Stan

f350ca

f350ca

EdK

f350ca

f350ca

f350ca