MetalworkingFun Forum

Full Version: Todays Project - What did you do today?
You're currently viewing a stripped down version of our content. View the full version with proper formatting.
Pages: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 500 501 502 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549
Good job Tom, I could do with 10 hrs of that type of work but at the rate I "peter out" it would take 5 days!
At first I wondered about "Next comes a toothbrush cleaning" but then I read further and understood.Rotfl
Today was ugly, but productive. I took the dead mouse out of the AC/heater blower in my truck. Grrr... I had to drive to town and back with that stench going along for the ride on Tuesday. Thank goodness the blower motor was relatively easy to remove. Now to wear out the smell.
Good thing you didn't need the heater. Blink

Try spraying some of that Fabreze air freshener stuff in the AC inlet. That should knock it down a bit.

Tom
Finished putting together a home made "Foul-Out" unit. (A low voltage reverse-plating power supply.) They quit making them a year or so back, and I wanted to get another one - but waited too long. Bash

[attachment=2729]
Hey Willie,

I assume you are using it for bores? What do you use for an electrode? I imagine it must be a wire the length of the barrel but somehow prevented from touching the bore.

Tom
Willie - could you not just open the box up and replicate the circuitry? Shouldn't be too difficult.
Tom,
Yes - using it for bore cleaning. Saves a lot of elbow grease and wear and tear on the bore by not scrubbing it to death with a bore brush. I used to think I was getting my barrels spotlessly clean with conventional methods - that is... until I bought a borescope and saw what was left behind. Jawdrop

The electrode is a length of stainless TIG rod with a couple of o-rings slipped over the rod. The o-rings keep the rod centered in the barrel. On the off chance that the rod accidentally contacts the barrel, there is a warning LED on the unit that signals the short - and you can correct it. The larger the bore, the larger the o-ring (O.D.) you use.

Darren,
There is nothing wrong with the original unit so there is nothing I have to repair/replace. I just wanted another one so I can run two of them at the same time. When I start cleaning after a trip to the range, I always have 4 - 6 "patients" lined up awaiting treatment.

Running two units instead of one will cut my clinic hours in half! Big Grin Big Grin Big Grin
So how in the world does this thing work?
Willie, I knew there was nothing wrong with your original unit. I was suggesting that you open the unit you have and copy the board. I have done this with several items where the original is either overpriced or no longer available.
Darren, sorry - I misunderstood your meaning. Fortunately I didn't have to open up my original unit and reverse engineer anything, because someone has already done that and made the schematic available online. The patent on the "Foul-Out" had run out years ago and sales were slow due to cost, so they dropped it.

Elijah, it basically works as an electro-chemical plating tank. The electrode goes inside the barrel and is attached to one side of a power supply. The bore is filled with a cleaning solution (electrolyte) and the barrel is attached to the other side of the power supply.

The electrical current passing between the two dissolves any lead or copper deposits inside the barrel and transfers them to the electrode (stainless rod) in the center of the bore. When its done you just remove the lead or copper coated rod from the now clean barrel. You don't have to spend hours scrubbing the barrel with a cleaning rod and bore brush. Smiley-dancenana

p.s.
I'm sure you know the guy that designed the circuit for the home made version. It was "UncleNick"! Smile
Pages: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 500 501 502 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549