Home Shop Made Tools
I made these step blocks based on Tom's thread.

http://www.metalworkingfun.com/showthread.php?tid=846

They're very handy and I use them all of the time.

Ed

         

         
Reply
Thanks given by: aRM
Sure are pretty Ed Thumbsup 
Smiley-eatdrink004 
DaveH
Reply
Thanks given by: EdK
Nice job Ed .. I didnt have these step blocks on my to do list but since i saw them again and ya did such a nice job you gave me inspiration to putem on the list . Right now i started on a set a paralels or my new mill vice, once im done with them i may start this project .
I like the thumb knob design w/ the added touch . Did you press fit make (a 2 pc knob) or other thanks

again Nice Job
Reply
Thanks given by:
(09-14-2015, 03:14 PM)Kennyv Wrote: Nice job  Ed ..  I  didnt have these step blocks on my to do list  but since i saw them again  and ya did such a nice job you gave me inspiration to  putem on the list . Right now i started on a set a paralels or my new mill vice, once im done with them i may start this project .  
I like the thumb knob design w/ the added touch . Did you press fit  make  (a 2 pc knob)  or other thanks

 again Nice Job

Thanks Kenny.

I pinned the knob to the bolt using a brass pin so it doesn't show up. There's not a lot of pressure on the knob since it's just used to keep the leafs from flopping around when using them and when on the shelf.

Ed
Reply
Thanks given by:
I made this spin indexer tailstock for my, well, spin indexer.  Smile
It was a fun project.

http://www.metalworkingfun.com/thread-2212.html

The first picture is not of my spin indexer tail stock but of the original designers version. It showed me what it should look like when I got mine done. I made a few changes to the design when I made mine.

Ed

         
Reply
Thanks given by: aRM
I like your one better Ed.
Hunting American dentists since 2015.
Reply
Thanks given by: EdK
Ed

i was in the middle of designing a tailstock for my RT and an indexer i am going to purchase, thats a perfect design i need, very clever.  Nice work on your one as well very sleek....

Anthony.
ieezitin, proud to be a member of MetalworkingFun Forum since Jan 2013.
Reply
Thanks given by: EdK
Very  Nice Job Ed  Clean slick ... Thumbsup

On the  spin indexer tailstock what is the function of the big knob?
thanks  again nice work .. lots of new ideas

Ed thanks yes i fig you pinned Bolt to knob but  i was referring to the knob  outside and inner diam looks like a press  fit or thats cosmetic?
Reply
Thanks given by: EdK
(09-16-2015, 01:46 PM)Kennyv Wrote: Very  Nice Job Ed  Clean slick ...  Thumbsup

On the  spin indexer tailstock what is the function of the big knob?
thanks  again nice work .. lots of new ideas

Ed thanks yes i fig you pinned Bolt to knob but  i was referring to the knob  outside and inner diam looks like a press  fit or thats cosmetic?

The big knob is for locking the arbor once you've got it into position.

The knobs for the step blocks are made of one piece of brass. Maybe that decorative circle on the top is fooling you into thinking it's a two-piece part. I put that in with a 'V' shaped tool bit just for decoration.

Ed
Reply
Thanks given by:
(09-16-2015, 03:27 PM)EdK Wrote: The big knob is for locking the arbor once you've got it into position.

The knobs for the step blocks are made of one piece of brass. Maybe that decorative circle on the top is fooling you into thinking it's a two-piece part. I put that in with a 'V' shaped tool bit just for decoration.

Ed

OOOOoooops
Sorry
We all lost here !!!??? 17428
aRM
Reply
Thanks given by:




Users browsing this thread: 4 Guest(s)