+- MetalworkingFun Forum (http://www.metalworkingfun.com)
+-- Forum: Machinery (http://www.metalworkingfun.com/forum-10.html)
+--- Forum: Milling Machines (http://www.metalworkingfun.com/forum-12.html)
+--- Thread: Fixing a Leaky RF-45 Mill Head - Enco (/thread-157.html)
RE: Fixing a Leaky RF-45 Mill Head - EdK - 04-05-2012
(04-05-2012, 05:54 PM)DaveH Wrote: Ed, I don't think that is expensive, bearings (good ones that is) have never been cheap. Nor have the seals.
DaveH
Dave,
That's the way I look at it to.
Ed
RE: Fixing a Leaky RF-45 Mill Head - Highpower - 04-05-2012
And it's cheaper than buying a new mill.
RE: Fixing a Leaky RF-45 Mill Head - EdK - 04-06-2012
(04-05-2012, 09:10 PM)Highpower Wrote: And it's cheaper than buying a new mill.
Except, I likely am buying a new mill. Just like the one Arvid ordered. But, I couldn't sell my current mill with a leaky head with a clear conscience so I have to get this mill all spruced up and functioning to a level that I would find acceptable if I were going to keep it.
Ed
RE: Fixing a Leaky RF-45 Mill Head - Highpower - 04-06-2012
Ahhh.... I see how it is now. You've been holding out on us!
That's cool. Getting a new machine or tool is always a sure way to brighten your day. Of course there is nothing wrong with having an extra one on hand for second operations. Just saying.....
RE: Fixing a Leaky RF-45 Mill Head - EdK - 04-09-2012
(04-06-2012, 07:33 AM)Highpower Wrote: Ahhh.... I see how it is now. You've been holding out on us!
That's cool. Getting a new machine or tool is always a sure way to brighten your day.
Willie,
Actually I've not been holding out. See this thread.
http://www.metalworkingfun.com/showthread.php?tid=65
Ed
RE: Fixing a Leaky RF-45 Mill Head - Highpower - 04-09-2012
I remember the thread, but I don't remember you actually ordering it yet.
But then again, since I have "oldtimers" disease - there isn't a whole lot I do remember these days.
RE: Fixing a Leaky RF-45 Mill Head - EdK - 04-27-2012
OK, it's time to get back to this project. I have most of the weekend allocated for working on the mill head rebuild. I have all of the parts and I finished my diversion project which was to drill and tap two holes in the mill head carrier so I can mount a bracket that will hold the gas springs on when I get around to that project.
Ed
RE: Fixing a Leaky RF-45 Mill Head - henryarnold - 04-28-2012
(04-27-2012, 08:13 PM)EdAK Wrote: OK, it's time to get back to this project. I have most of the weekend allocated for working on the mill head rebuild. I have all of the parts and I finished my diversion project which was to drill and tap two holes in the mill head carrier so I can mount a bracket that will hold the gas springs on when I get around to that project.
Ed
Ed,
I'm on vacation this week so I'll be starting the work on my leaky mill. I'm looking forward to your posts showing how you finished the work.
Henry Arnold
RE: Fixing a Leaky RF-45 Mill Head - EdK - 04-28-2012
Henry,
Thanks for putting the pressure on.
Now I really need to get this done.
Ed
RE: Fixing a Leaky RF-45 Mill Head - EdK - 04-28-2012
How does one properly install seals? See picture below. I have to install the one I got started, and can't get to go any further with hand pressure, and then the second one installs on top of the first.
Ed
[attachment=940]