+- MetalworkingFun Forum (http://www.metalworkingfun.com)
+-- Forum: Machinery (http://www.metalworkingfun.com/forum-10.html)
+--- Forum: Milling Machines (http://www.metalworkingfun.com/forum-12.html)
+--- Thread: Let's See Your Mill (/thread-16.html)
RE: Let's See Your Mill - NormanV - 11-22-2014
Thank you for the kind comments, it was quite an adventure building it. My next job is a tailstock for the rotary table. I am thinking about an internal combustion engine as a future project.
RE: Let's See Your Mill - Vinny - 12-11-2014
New member here, first post. Here's my old mill. It's an old Bromson Number 7, made in Detroit. There's some condos or apartments now where the factory used to be.
The mill is alot cleaner now than in this pic but I haven't taken any pics lately. It was quite a rusty mess when I got it. The motor may very well be the original motor, it's only 1/4 HP but it hasn't slowed down for anything I've done on it. The Y axis (in out) was missing the crank so I made one out of some aluminum I had laying around. The X axis crank (can't see it in this pic) doubles as the Z axis (up/down) crank. There is no quill but I really haven't missed it. The main limitation is it uses 3C collets and those don't go much above 1/2". In the pic it's mounted to a benchtop.
![[Image: mill6.jpg]](http://metalshop.nobucks.net/mill6.jpg)
Vince.
RE: Let's See Your Mill - schor - 12-11-2014
Here's pics of my mills.
This benchtop horizontal weights about 300lbs. I'll be restoring this over the winter.
![[Image: IMG_20141123_194510.jpg]](https://lh5.googleusercontent.com/-wJQYsZLGCik/VIiTUYjCe6I/AAAAAAAACsw/OhcXyuBrApY/s807-no/IMG_20141123_194510.jpg)
And here's my little benchtop vertical mill.
![[Image: IMG_00000218.jpg]](https://lh4.googleusercontent.com/-gDV9nxBvBmA/UnbqrDHKK-I/AAAAAAAABsE/wP40A6SwiOA/s807-no/IMG_00000218.jpg)
RE: Let's See Your Mill - DaveH - 12-11-2014
Hi Vince,
A nice sturdy looking mill you have there
and
to MetalworkingFun 
DaveH
RE: Let's See Your Mill - DaveH - 12-11-2014
Steve,
Heck of a bench top horizontal mill
The vertical is more like it
nice machine DaveH
RE: Let's See Your Mill - vtsteam - 12-11-2014
![[Image: AtlasMill.jpg]](http://i786.photobucket.com/albums/yy150/vtsr/vtsr/Shop/AtlasMill.jpg)
My Atlas horizontal mill. I used to use it as a "vertical" too, with end mills and an angle plate since the arbor takes a 2MT and I have a range of collets and mill holders to fit. I also have a miniature MT2 3 jaw chuck that fits.
RE: Let's See Your Mill - PixMan - 12-13-2014
I wish I had room for a horizontal at times, and envy those who have them. Nothing better for deep slotting and gear cutting (short of a Gleason gear hob.)
RE: Let's See Your Mill - Mayhem - 12-13-2014
(12-13-2014, 11:13 PM)PixMan Wrote: I wish I had room for a horizontal at times, and envy those who have them. Nothing better for deep slotting and gear cutting (short of a Gleason gear hob.)
All I'm going to say is that I have seen your basement...
RE: Let's See Your Mill - PixMan - 12-17-2014
If you think I'm going to start a second machine shop in my home, yer nuts man.
RE: Let's See Your Mill - Mayhem - 12-17-2014
(12-17-2014, 07:36 AM)PixMan Wrote: If you think I'm going to start a second machine shop in my home, yer nuts man.
Nope - I've been tested