MetalworkingFun Forum
Coke Forge Build - Printable Version

+- MetalworkingFun Forum (http://www.metalworkingfun.com)
+-- Forum: Machining (http://www.metalworkingfun.com/forum-5.html)
+--- Forum: Welding & Casting (http://www.metalworkingfun.com/forum-9.html)
+---- Forum: Blacksmithing (http://www.metalworkingfun.com/forum-29.html)
+---- Thread: Coke Forge Build (/thread-2189.html)

Pages: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36


RE: Coke Forge Build - RobWilson - 05-17-2015

Well I just messed about today , cleaning the shop .


Decided  I am going make an  extraction hood  for the forge ,so I dug out this heating fan from the loft . 


[Image: P1080931_zpsstnyynrh.jpg]

It shifts a fare old bit of air , only thing is the motor is in the wrong place for my needs . So I removed the motor ,stripped the motor and swapped the field coils around 
so the motor would spin in the opposite direction ,and mounted the motor on the other side of the fan case . 

[Image: P1080936_zpstzqhacly.jpg]


Being on the outside with little air flow for cooling I ran it for a couple of hours to see if it would overheat ,its was fine peak temp was 65c , time to come up with a hood design . 


Rob  


RE: Coke Forge Build - hermetic - 05-17-2015

Rob, Are you going to put the fumes directly through the fan? most flue assisters I have seen blow into a tee across the top of the fume inlet and extract by venturi effect. Mind you, you will get psoitive fume extraction and if the hood is a fair bit above the forge it will draw enough cooler air in to keep the fan and duct fairly cool. I am going to have to do something along these lines for mine. Good to see it lit, and glad it didn't put the fire all over the shop. Of course the whole groupwill want a video of it when it's finished! You can often find that woodburner suppliers sell thin (around 1") firebrick in flat sheets to cut up, you could make a lining with that. http://www.ebay.co.uk/itm/DIY-FIRE-BRICK-VERMICULITE-FIRE-BOARD-1-4-SHEET-CUT-YOUR-OWN-FIRE-BRICKS-/251259107303
Superb job!
Phil


RE: Coke Forge Build - RobWilson - 05-17-2015

Hi Phil 

Yes I will be sucking the fumes through the fan , It will be drawing from a  600x600 hood so I reckon it will survive  Big Grin  , cheers for the link mate  6799 


Rob 


RE: Coke Forge Build - RobWilson - 10-24-2015

Hi Chaps  Big Grin


Decided to do a bit work on the forge today , welded some very old and rusty steel onto the stand for feet . 


[Image: P1100460_zpsf51oe6oq.jpg]
[Image: P1100461_zpsbz5eppz3.jpg]
[Image: P1100465_zpshopfhzfq.jpg]

and decided to cut a section of the hearth away  . 

before .


 [Image: P1070984_zpsccb571e6.jpg]


after  Big Grin

[Image: P1100473_zpsrainui0d.jpg]


First time I have used the yard vice ,


[Image: P1080945_zpstvjvoqbx.jpg]




 much better grinding out side , needs two mods , it's about 2" to high and it needs somewhere to hand a grinder  Chin   . 



Rob  Drinks


RE: Coke Forge Build - EdK - 10-24-2015

Nice welds Rob.

Ed


RE: Coke Forge Build - RobWilson - 10-25-2015

Cheers Ed ,,,,,,,,,,, Smiley-eatdrink004


Got a tad more done today ,was going great guns up until I pulled a muscle in my back  Bash , so I will post this for now  Smile  , first job this morning was to cut down the yard vice stand

by 2" and add two bits of flat bar so that I can hang gear from them . 

 [Image: P1100476_zps51vjxl3x.jpg]
 [Image: P1100483_zpsgszinhzc.jpg]
[Image: P1100479_zpsnjk9v4bb.jpg]

Then another job I have been meaning to do is add a hook to the 8" grinder , this was made from a bolt . 

 [Image: P1100488_zps9mhawys2.jpg]
[Image: P1100489_zps0i23w8um.jpg]
[Image: P1100490_zpssf4g9hzr.jpg]
[Image: P1100492_zpswzzl3jef.jpg]


That done I could get back on with the forge , I am using up my old rusty stock on this project , this was cleaned up with the above grinder . 

[Image: P1100494_zpshqkakl1i.jpg]


and cut and welded into this . 

[Image: P1100495_zpsrrjetyya.jpg]


this being to support the hood and back panel . 

[Image: P1100500_zps6wqmbw5d.jpg]
[Image: P1100502_zpsalwo3xyq.jpg]

deciding whether to bolt or weld it to the hearth Chin


cheers Rob


RE: Coke Forge Build - doubleboost - 10-25-2015

Very nice Mate
I see it is starting to get a bit weight & size about it lol


RE: Coke Forge Build - krv3000 - 10-25-2015

brill work as per rob


RE: Coke Forge Build - DaveH - 10-25-2015

Nice work Rob, outside vice for grinding - good idea. Thumbsup 
Smiley-eatdrink004 
DaveH


RE: Coke Forge Build - Roadracer_Al - 10-26-2015

I like the bars for hanging tools. I keep thinking I need to build myself a hammer stand. My hammers are in the bottom drawer of my tool chest, and they're slowly destroying the slides b/c they're too heavy.

Hope your back feels better!