MetalworkingFun Forum
5 Cylinder Radial - Printable Version

+- MetalworkingFun Forum (http://www.metalworkingfun.com)
+-- Forum: Machining (http://www.metalworkingfun.com/forum-5.html)
+--- Forum: Projects (http://www.metalworkingfun.com/forum-7.html)
+--- Thread: 5 Cylinder Radial (/thread-2632.html)

Pages: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28


RE: 5 Cylinder Radial - Brian - 04-29-2020

Oh how i wish it was truly Job totally done, unfortunately it's just the spinner, and that breeds another job of making the starter drive with a rubber lining and a sprag clutch to catch the over run.
Lot's more to do
Brian.


RE: 5 Cylinder Radial - Pete O - 04-29-2020

Ah well, we'll be patient. I figured you at least had an ignition system to create yet before we hear it purr.


RE: 5 Cylinder Radial - Dr Stan - 04-29-2020

I'm thinking a RC biplane.


RE: 5 Cylinder Radial - Highpower - 04-30-2020

(04-29-2020, 01:27 AM)Brian Wrote: Oh how i wish it was truly Job totally done, unfortunately it's just the spinner, and that breeds another job of making the starter drive with a rubber lining and a sprag clutch to catch the over run.
Lot's more to do
Brian.

Starter drive? Methinks you've spoiled yourself Brian. When I was a youngster all we had were "chicken sticks". Big Grin

Just kidding. When I had my helo the starter drive / fuel pump box was an absolute necessity.


RE: 5 Cylinder Radial - Brian - 06-19-2020

Now it's back to the serious stuff, making piston rings.
Just turn a tube of Iron a little oversize.
Split it lengthwise to create the ring gap.
Clamp it in the chuck tightly to close the gap.
Turn the ring to size inside and out.,
Part off. 
26mm diameter--- 1.5mm wide---1mm thick.

There now that was simple wasn't it ?????

[attachment=16645]

Brian.   Smiley-dancenana


RE: 5 Cylinder Radial - pepi - 03-24-2021

(04-29-2020, 01:27 AM)Brian Wrote: Oh how i wish it was truly Job totally done, unfortunately it's just the spinner, and that breeds another job of making the starter drive with a rubber lining and a sprag clutch to catch the over run.
Lot's more to do
Brian.

 Very nice Brian

Has come a long way since the last time I saw it. Perfect way to spend time  indoors.

Pep


RE: 5 Cylinder Radial - Brian - 03-28-2021

[attachment=16888]

Steady progress being made, .  The ignition system is nearly done  just the hall sensors to be mounted.   Then i need a stand for the engine so i can get on with the Oil and Fuel tanks.  Battery. Tach. Throttle.  ETC  ETC
Brian Smiley-dancenana


RE: 5 Cylinder Radial - Vinny - 03-28-2021

Looks great and gettin close!!


RE: 5 Cylinder Radial - TomG - 03-28-2021

(03-28-2021, 11:41 AM)Brian Wrote:         Steady progress being made, .  The ignition system is nearly done  just the hall sensors to be mounted.   Then i need a stand for the engine so i can get on with the Oil and Fuel tanks.  Battery. Tach. Throttle.  ETC  ETC
Brian Smiley-dancenana

It's coming along nicely, Brian. I applaud you perseverance. Worthy 

What did you use for spark plugs?

Tom


RE: 5 Cylinder Radial - Brian - 03-28-2021

Hi Tom The plugs are from the hit and miss engines sold by Banggood. I
also have kits from Hemingway. to make circular discharge plugs if necessary.
Just beginning to se a light at the end of the tunnel.
Brian.