+- MetalworkingFun Forum (http://www.metalworkingfun.com)
+-- Forum: Machining (http://www.metalworkingfun.com/forum-5.html)
+--- Forum: Projects (http://www.metalworkingfun.com/forum-7.html)
+--- Thread: [IDEA] Converting a vertical wood band saw to metal cutting (/thread-3479.html)
Converting a vertical wood band saw to metal cutting - n2xd - 01-30-2017
Has anyone out there converted a vertical wood band saw to metal cutting? Looking for ideas. I have a Porter cable 14" that I'm thinking would serve me better as a metal cutting saw. Thanks.
RE: Converting a vertical wood band saw to metal cutting - Bill Gruby - 01-30-2017
I did it 5 years ago. I started with a busted up harbor freight saw. I slowed it down with a 60:1 gear box run by the original motor.
"Billy G"
RE: Converting a vertical wood band saw to metal cutting - f350ca - 01-30-2017
A chap said he had what he thought was a bandsaw, did I want it. From what he said I figured it was an old 14 inch one that I was set to convert. When he brought it over, turned out to be a 14 inch Delta with the metal cutting gearbox built in. Just needed cleaned up. Used it this morning, works great.
RE: Converting a vertical wood band saw to metal cutting - EdK - 01-30-2017
I believe Tom converted his wood band saw to use for metal cutting.
Ed
RE: Converting a vertical wood band saw to metal cutting - pepi - 01-30-2017
Yeah I can tell you how to do that and give some part numbers.
The saw 14" delta
Speed reduction kit made by Jet $ 121.00: part 3SP-14 Three Speed Kit
From Grainger a 10.5 pulley attached to the blade drive shaft.
I will also suggest a quality blade. I have found this to be a good one:
http://www.lenoxtools.com/Pages/diemaster-2-bi-metal-band-saw-blades.aspx?Redirect=1
[attachment=14190]
[attachment=14191]
Using it for about a decade..
Greg
RE: Converting a vertical wood band saw to metal cutting - n2xd - 01-31-2017
Thanks for the information. I'm going to look into the Jet kit.
RE: Converting a vertical wood band saw to metal cutting - schor - 01-31-2017
Depending on the bandsaw, you could add another pulley. I saw it done on some forum but cannot remember where now.
RE: Converting a vertical wood band saw to metal cutting - Dr Stan - 02-05-2017
I have one of the factory built Rockwell's that cut wood & metal. It's a great saw. I had planned on converting a Taiwanese built wood saw, but jumped on the Rockwell before I started on the conversion. Sold it for what I had in it.
The kit looks much better than most could build and probably cheaper than all the parts, etc one would need such as a gear box to slow down the blade. At the Surplus Center a 60:1 gear box is $98.45 plus shipping. My SWAG is that shipping would raise it to at least $125.00, equal to the kit. All said and done I think conversion would cost $175 or more.
Ditto on the quality blades. One can buy decent wood blades at a big box store, but metal ones need to be sourced from an on line store.
RE: Converting a vertical wood band saw to metal cutting - Pumpjack - 05-04-2017
I guess this is a old thread , but i converted my Delta 14 inch with a transmission from a older riding mower. 3 speed gearbox with a reverse. LoL had to still pulley it down some to get it slow enough but now i can cut steel in first gear and go to 3rd gear for wood.
RE: Converting a vertical wood band saw to metal cutting - Dr Stan - 05-04-2017
(05-04-2017, 10:06 PM)Pumpjack Wrote: I guess this is a old thread , but i converted my Delta 14 inch with a transmission from a older riding mower. 3 speed gearbox with a reverse. LoL had to still pulley it down some to get it slow enough but now i can cut steel in first gear and go to 3rd gear for wood.
Some pics would be nice.