MetalworkingFun Forum
Herless (rebranded Ta Fu Yuan) TFY-618 Surface Grinder - Printable Version

+- MetalworkingFun Forum (http://www.metalworkingfun.com)
+-- Forum: Machinery (http://www.metalworkingfun.com/forum-10.html)
+--- Forum: Other Machinery (http://www.metalworkingfun.com/forum-13.html)
+---- Forum: Surface Grinders (http://www.metalworkingfun.com/forum-31.html)
+---- Thread: Herless (rebranded Ta Fu Yuan) TFY-618 Surface Grinder (/thread-3841.html)

Pages: 1 2


RE: Herless (rebranded Ta Fu Yuan) TFY-618 Surface Grinder - Vinny - 02-22-2018

I just found this in an archive someplace from a guy named Harold:

Quote:The angle isn't for performance, it's to insure long life of the diamond. If the diamond is used at a fixed angle, regardless of the angle, a flat forms that isn't the best condition for a diamond to be used. As has been mentioned already, a diamond with a flat tends to dull the newly exposed abrasive bits. The angular mount allows for a change of attitude of the diamond. It is commonly accepted that diamonds are mounted in holders that provide the angle, although I am far more familiar with 10° than 15°.



RE: Herless (rebranded Ta Fu Yuan) TFY-618 Surface Grinder - SteveG - 02-22-2018

(02-22-2018, 11:36 AM)Vinny Wrote: This page has a lot of useful info on surface grinders, and grinders/grinding in general.  Unfortunately all it says about the dresser is "slight angle".  As I recall, when I made mine, somewhere I found the number 5 degrees so that's what I went with.

http://www.americanmachinetools.com/how_to_use_a_surface_grinder.htm

Great info there Vinny.

Figure 5.14 has a good diagram and states "Slant the diamond 3° to 15° in the direction of rotation and 30° to the plane of the wheel as shown in Figure 5-14 to prevent chatter and gouging."

There's other good dressing info in that section too.

Steve



RE: Herless (rebranded Ta Fu Yuan) TFY-618 Surface Grinder - SteveG - 02-26-2018

I've decided I'm going to convert the grinder back to manual rather than work on getting the pneumatics going right now.
Multiple reasons but mainly I think its going to be easier to learn using a fully manual machine.

Currently my cross feed shaft is missing the handwheel, but it has a chain sprocket on the drive end. The decal on the wheel guard mentions the need to adjust the cable after prolonged use, so I figure it was originally cable driven. Seems reasonable to return it back to that.
So I'll need a handwheel, cable drum, and some cable/fittings.
Doing some rough on-screen measuring from a photo I found of my model, it looks like the handwheel should be about 9" diameter. Does that seem about right?
Trying to work out the traverse rate, I found an online spec with a travel of 2.7"/rev for a similar 6x18 grinder. I've also found photos of a Norton machine that appears to have a drum around 2" diameter (so ~6"/rev assuming direct drive)

Anyone with a grinder care to give me a sanity check on the travel rate?

Steve


RE: Herless (rebranded Ta Fu Yuan) TFY-618 Surface Grinder - Pete O - 03-01-2018

I took a couple of measurements on my grinder this afternoon Steve, the X-axis handwheel is 200mm O.D. and the X-axis travels 120mm per revolution. Also I checked the angle of the diamond in the dresser, it is 7.5 degrees from vertical. The picture below shows the dressing jig, I did find the hole in the base useful, it enabled me to bolt it to an angle block to dress the side of the wheel using Z-axis travel the couple of times I have wanted to side-wheel, the first of which was to grind the back fence of the chuck parallel to X.
[attachment=15602]
[attachment=15603]

Edit; just re-read your last post and thinking about the drive, it could be that there was a chain drive with the free ends of the chain connected by a cable, or connected to the underside of the table by a cable. A chain and sprocket would provide relatively positive position locking of the X-axis when this is required (such as dressing), mine is locked at the handwheel axle rather than the table itself.


RE: Herless (rebranded Ta Fu Yuan) TFY-618 Surface Grinder - SteveG - 03-01-2018

Awesome - thanks for the info Pete.

I managed to find a suitable size handwheel in the scrap junk at work. Its much more solid than required so I think will go on a diet in the lathe - just to thin it a bit in general to reduce the mass without spending too much time.
Bore just needs to be opened up about 3mm to suit the grinder shaft, and think I'll modify the current solid crank handle so that it runs in a bush while I'm at it
[attachment=15605]


Steve


RE: Herless (rebranded Ta Fu Yuan) TFY-618 Surface Grinder - SteveG - 03-05-2018

Last night I removed the table to take a better look. It was definitely chain drive before the pneumatic conversion:

[attachment=15629]

Removed the handwheel shaft and its outer housing. Bearings are only single metal shield type and rough.

Also found that although there's plenty of oil output at the oiler, nothing is coming out the delivery holes in the ways. Guess they are full of old gunge that was once oil, so another one for the task list.

Picked up a couple of new bearings today, and a box of chain to match the sprocket. Hoping I might get lucky and find that the pins in the chain are the same size as the adjuster block on the table:

[attachment=15630]

Steve


RE: Herless (rebranded Ta Fu Yuan) TFY-618 Surface Grinder - SteveG - 03-05-2018

New chain is a perfect fit:

[attachment=15631]

Steve


RE: Herless (rebranded Ta Fu Yuan) TFY-618 Surface Grinder - Pete O - 03-05-2018

That makes the decal that you mentioned earlier, alluding to adjustment of a cable, a bit of a mystery, doesn't it?


RE: Herless (rebranded Ta Fu Yuan) TFY-618 Surface Grinder - SteveG - 03-05-2018

I thought so initially, but now convinced the chain drive is definitely a conversion - the boss for the sprocket is welded onto the sprocket then machined off (leaving a small bit of weld unmachined), and the adjuster also looks like its been shop made rather than a factory made part.

So I'm guessing originally cable, converted to chain, then pneumatic, and now being converted back to chain :)

Steve