MetalworkingFun Forum
[PROJECT] Bar Stock Steam Engine - Printable Version

+- MetalworkingFun Forum (http://www.metalworkingfun.com)
+-- Forum: Machining (http://www.metalworkingfun.com/forum-5.html)
+--- Forum: Projects (http://www.metalworkingfun.com/forum-7.html)
+--- Thread: [PROJECT] Bar Stock Steam Engine (/thread-4293.html)

Pages: 1 2 3 4 5 6 7


RE: Bar Stock Steam Engine - Cross Slide - 05-17-2021

(05-17-2021, 08:39 AM)TomG Wrote: Excellent!

This project is helping you learn the value of fixturing in machining.

Tom


Your right. This project has already taught me a lot. It has also given me the opportunity build some of the tools, equipment, and fixtures I have wanted to build but haven’t gotten around to!!
I’m positive I will learn a lot more as I proceed. I’m getting to do a lot of new operations as well. One of the next parts will be the Cam. This will require a rotary table which I haven’t used before. 

Trevor


RE: Bar Stock Steam Engine - Cross Slide - 12-05-2021

After taking the summer off from my project I finally have gotten back into the shop. I had a few hours available today to do some machining. I started back with machining the Cam. It started out as a piece of 1.5” cold roll that I turned down to 1.25” and parted off to 1” long. 
I then had to drill two holes as well as open the top portion up so only the bottom portion of the holes where threaded for 8-32 set screws. Then I tapped the holes using a small tap handle the I built last spring. 
[attachment=17356]
[attachment=17357]
[attachment=17358]
[attachment=17359]

After those holes where done I needed to stand it up vertical and drill a .500 hole directly inline with the two holes but .250 off of centre to give me the cam action. My DRO made this a easy operation. I drilled the hole out and finished it with my .500 reamer for the perfect fit on the crank shaft.
[attachment=17360]
[attachment=17361]
[attachment=17362]
[attachment=17363]
[attachment=17364]
[attachment=17365]
[attachment=17366]
[attachment=17367]
[attachment=17368]
[attachment=17369]

Trevor


RE: Bar Stock Steam Engine - Cross Slide - 12-13-2021

I got a few of the small parts done last weekend. I started off by making the Air Tubes that fit between the Valve Body and Cylinder. I made these out of 1/4” A2 Drill Rod instead of just using cold roll like that plans called for. I like the look of Drill Rod better then Cold Roll. They are .500 long with a .125 hole to allow the air to pass through. 

[attachment=17371]
[attachment=17372]
[attachment=17373]
[attachment=17374]

Then I machined the pin that will connect the Valve Rod to the Valve. It is made out of the same 1/4 Drill Rod. The fun part of this one was the cross drilled hole through the end of the pin. #60 Drill.

[attachment=17375]
[attachment=17376]
[attachment=17377]
[attachment=17378]
[attachment=17380]
[attachment=17381]
[attachment=17382]

Trevor


RE: Bar Stock Steam Engine - JScott - 12-13-2021

Making progress!


RE: Bar Stock Steam Engine - Cross Slide - 12-13-2021

This is the Rod the connects to the piston and passes through the back side of the cylinder to the slide that the connecting rod attaches to. 1/4” drill rod with 6-32 threaded holes in each end. 

[attachment=17383]
[attachment=17384]
[attachment=17385]

The final part from this weekend was the Valve Rod. Made out of .125 Drill Rod with both ends threaded. 

[attachment=17386]
[attachment=17387]
[attachment=17388]

All simple parts machined this weekend. But a few off the list.

Trevor


RE: Bar Stock Steam Engine - EdK - 12-13-2021

Nice work Trevor! Thumbsup


RE: Bar Stock Steam Engine - Cross Slide - 12-26-2021

Made some more progress on the bar stock steam engine. I finished up the three pillow blocks that will support the crank shaft. They are made out of 3/8” thick aluminum plate. I first cut the blocks a bit larger then required. Then I milled the blocks to the final width, but I left them slightly oversized for the height. 

I them found the back left corner and started off by plunge cutting the hole for the bushing with a .625 end mill using a vise stop for repeatability. 

[attachment=17439]
[attachment=17440]
[attachment=17441]
[attachment=17442]

Once that was done in each block I set them back up and used my boring head to take the hole out to a press fit for oil lite bushings. I overshot my target dimensions slightly on the first one. Found out that the dial on the boring head isn’t perfectly accurate. So from then on once I was close I would advance the cut with a dial gauge on the boring head. That solved the problem. Luckily the first block is still useable. Tom G told me to do a lite knurle on the bushing to help make it a press fit again. 

[attachment=17443]
[attachment=17444]
[attachment=17445]

I then located and drilled the two mounting holes into the bottom of each block. Then I plunge cut two holes on the face of each block to give me the radius at the bottom the blocks and open up the tops of the mounting holes. 

[attachment=17446]
[attachment=17447]
[attachment=17448]

Trevor


RE: Bar Stock Steam Engine - Cross Slide - 12-26-2021

I then was able to use my rotary table for the first time to cut the upper radius on the pillow blocks. I started off by plunge cutting all the way around the radius. Then moved in to the finished size and did a final cut. 

[attachment=17449]
[attachment=17450]
[attachment=17451]
[attachment=17452]

Once that was done I cut the excess material off with my vertical band saw. Then I finished the pillow blocks up on my mill using a fixture plate I made when I machined the connecting rod. 

[attachment=17453]
[attachment=17454]
[attachment=17455]
[attachment=17456]

The final step will be to polish them to a mirror finish at a later date, and press in the oil lite bushings. 

Trevor


RE: Bar Stock Steam Engine - Vinny - 12-26-2021

Looks good!!!


RE: Bar Stock Steam Engine - EdK - 12-26-2021

Smiley-signs009

Ed