MetalworkingFun Forum
Building The Steven's Favorite - Printable Version

+- MetalworkingFun Forum (http://www.metalworkingfun.com)
+-- Forum: Machining (http://www.metalworkingfun.com/forum-5.html)
+--- Forum: Gunsmithing (http://www.metalworkingfun.com/forum-27.html)
+--- Thread: Building The Steven's Favorite (/thread-506.html)

Pages: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27


RE: Building The Steven's Favorite - EdK - 09-30-2012

Nicely made tool Tom. 6799

Ed


RE: Building The Steven's Favorite - Highpower - 09-30-2012

Be careful you don't end up drilling into your compressor tank. Rotfl


RE: Building The Steven's Favorite - TomG - 09-30-2012

(09-30-2012, 10:37 PM)Highpower Wrote: Be careful you don't end up drilling into your compressor tank. Rotfl

Ya know Willie, I think the damn thing would actually reach it. Yikes


RE: Building The Steven's Favorite - TomG - 10-07-2012

I caught the plague last week so productivity took a bit of a dive. Feeling better this weekend, I managed to put a few hours in on the drilling rig for the Steven's. This is the guide plate used to start the gun drill on center in the end of the barrel. It consists of a plate attached to the ways of the lathe with a drill guide bushing mounted in a hub with a bit of adjustment built in to allow the bushing to be precisely centered on the spindle.

The next step is to make a chip box that attaches to the plate to catch the chip laden cutting oil as it sprays out the end of the barrel during the drilling procedure. It'll just be a simple sheet metal box with some sort of rubber seal on the holes where the drill passes through, and a drain out the bottom.

Tom

[Image: 005_12.JPG]

[Image: 006_9.JPG]


RE: Building The Steven's Favorite - Mayhem - 10-08-2012

One of those squirrels bite you Tom?

Ill or not, that looks good and I'm looking forward to the chips and oils flying!


RE: Building The Steven's Favorite - EdK - 10-08-2012

Smiley-signs021 and 6820

Ed


RE: Building The Steven's Favorite - TomG - 10-08-2012

(10-08-2012, 05:19 AM)Mayhem Wrote: One of those squirrels bite you Tom?

Ill or not, that looks good and I'm looking forward to the chips and oils flying!

No, no squirrel bites Darren. In fact, I haven't seen many of the little buggers around lately. I suspect they may be tending to their nuts this time of year. Unlike where you are, winter is fast approaching around here. It was 30Fº (-1.1111111C) this morning and I had to scrape heavy frost off my windshield (windscreen).

Tom


RE: Building The Steven's Favorite - DaveH - 10-08-2012

(10-08-2012, 06:32 AM)TomG Wrote: No, no squirrel bites Darren. In fact, I haven't seen many of the little buggers around lately. I suspect they may be tending to their nuts this time of year. Unlike where you are, winter is fast approaching around here. It was 30Fº (-1.1111111C) this morning and I had to scrape heavy frost off my windshield (windscreen).

Tom

Nicely done Tom Smiley-signs107

It was 30 deg. here yesterday as well Tom Thumbsup ah ..... 30C deg. Rotfl
Smiley-eatdrink004
DaveH


RE: Building The Steven's Favorite - TomG - 10-08-2012

(10-08-2012, 07:52 AM)DaveH Wrote:
(10-08-2012, 06:32 AM)TomG Wrote: No, no squirrel bites Darren. In fact, I haven't seen many of the little buggers around lately. I suspect they may be tending to their nuts this time of year. Unlike where you are, winter is fast approaching around here. It was 30Fº (-1.1111111C) this morning and I had to scrape heavy frost off my windshield (windscreen).

Tom

Nicely done Tom Smiley-signs107

It was 30 deg. here yesterday as well Tom Thumbsup ah ..... 30C deg. Rotfl
Smiley-eatdrink004
DaveH

Yes, but you guys are getting closer to the sun, while we are tipping farther away. I test fired the furnace yesterday to make sure it was up to snuff before the bottom falls out of the thermometer. Bleh

Tom


RE: Building The Steven's Favorite - dallen - 11-05-2012

Tom what process or chemicals do you use to blue you work with????