+- MetalworkingFun Forum (http://www.metalworkingfun.com)
+-- Forum: Machining (http://www.metalworkingfun.com/forum-5.html)
+--- Forum: How-To's (http://www.metalworkingfun.com/forum-8.html)
+--- Thread: How to Indicate A Vise in Just One pass (/thread-511.html)
RE: How to Indicate A Vise in Just One pass - Highpower - 06-19-2012
I've seen Tom's video on this previously, and have been using it ever since on regular machine vices. (I don't own a swivel base.)
I'm happy to report it works equally well with a standard vice.
One of the best machining tips I have ever gotten!
Bravo Tom.
Willie
RE: How to Indicate A Vise in Just One pass - krv3000 - 06-20-2012
a good post
RE: How to Indicate A Vise in Just One pass - DanH - 06-20-2012
(06-19-2012, 09:17 PM)TomG Wrote:(06-19-2012, 09:03 PM)DanH Wrote: So if you don't have a swivel base (or don't have it installed) will this technique still work? Could you have the vice swivel about one of the lock down bolts? It looks so easy on the video that if I had to I could just about talk myself into buying the swivel base for my vise.
Great "how to" thanks.
Dan
Thanks Dan.
I don't know how well it will work without a swivel base, I've always had them on my vises. Why don't you try it out and let us know? It sounds like it might work leaving one bolt loose.
Tom
Tom,
I tried it last night and it worked great. Thanks again for the tip.
Dan
RE: How to Indicate A Vise in Just One pass - DaveH - 06-20-2012
Tom,
Brilliant
Terrific idea
DaveH
RE: How to Indicate A Vise in Just One pass - NevadaBlue - 07-23-2012
That is as good as an Easy Button! Thanks Tom!
RE: How to Indicate A Vise in Just One pass - TomG - 07-23-2012
(07-23-2012, 07:06 PM)NevadaBlue Wrote: That is as good as an Easy Button! Thanks Tom!
Thanks Ken, I'm glad you liked it. It's been a while since I've done any videos, maybe it's about time for a new one.
Tom
RE: How to Indicate A Vise in Just One pass - Tony Wells - 07-23-2012
One of these days I have to get a video camera. That's all there is to it. Lookout Youtube then!
RE: How to Indicate A Vise in Just One pass - TomG - 07-23-2012
(07-23-2012, 08:26 PM)Tony Wells Wrote: One of these days I have to get a video camera. That's all there is to it. Lookout Youtube then!
Tony,
I seriously doubt you could do anything to YouTube that hasn't already been done, but it is a lot of fun making your own movies.
Tom
RE: How to Indicate A Vise in Just One pass - Wawoodman - 09-08-2012
I tried it yesterday. The problem I'm having is that my needle runs true for part of the way, and then moves. And sometimes it seems to work fine, but when I go the other way, it's way off. So it's one of two things, to my mind: either the jaw is not truly flat, or my indicator (Starrett Last Word) is sticking. Both the indicator and the vise are eBay purchases.
If I remove the jaw, is the vise body accurate enough to work from? If it's the indicator, can it be serviced economically enough to make it worthwhile? Or should I be looking for a new one?
RE: How to Indicate A Vise in Just One pass - TomG - 09-08-2012
Put the indicator against the side of your table and run it back and forth. It's sounds like the gibs in the table may be loose or worn. Also try rocking the table by hand, deflection should be minimal. If it's the vise jaw you would get the same reading regardless of which way you feed it. If it's the indicator sticking, you should be able to see it moving the stylus by hand.
Tom