MetalworkingFun Forum
Todays Project - What did you do today? - Printable Version

+- MetalworkingFun Forum (http://www.metalworkingfun.com)
+-- Forum: Machining (http://www.metalworkingfun.com/forum-5.html)
+--- Forum: Projects (http://www.metalworkingfun.com/forum-7.html)
+--- Thread: Todays Project - What did you do today? (/thread-727.html)

Pages: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 500 501 502 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549


RE: Todays Project - What did you do today? - PixMan - 03-16-2014

Got back from a business trip to Nashville (and a stop ay my brother's place in Durham NC on the way back) yesterday, headed to the shop today to try and salvage the screw I had started making for Darren. No hope, as the threading insert had dug in too deep on the load side of the thread flank. And that was my second attempt. Bash

Third time a charm, thankfully! Smile

As I'd done with my second attempt, I first turned a wide groove in the area of where the gear will eventually sit. This gives me a generous landing spot for pulling out the half nut while threading a 5 thread per inch thread at 120 rpm.

Here's a shot of the piece after I finished threading and before I cleaned the coolant out of it:
[Image: DSC_0464-r_zpsa6f3a4e7.jpg]

This close-up shot is so detailed it looks somewhat rough, but it really is quite nice and not a trace of chatter despite the 18.7" of thread length. My machine doesn't have a follower rest, so that's hard to do!
[Image: DSC_0468-r_zps42d13e61.jpg]

Here's a shot of the three flats I had first milled on the end going in the 3-jaw chuck. When I made my first attempt, the finished 20mm diameter spun in the chuck from having too much tool pressure as I threaded. I probably should have cleaned off the cosmolene gunk from the 8 year old (but still new) 12" 4-jaw independent chuck I have that's never been on the machine. Too lazy to drag it out when this worked fine both times.
[Image: d5546e56-85fc-440e-92f5-ddacf28d6c98_zps81943502.jpg]

I'm just happy to have this part of the project done, finally! Finishing up the diameters, thread and keyways will be simple, despite the interrupted first cut I'll have.

I think I'll leave it as is and start on the mating bronze nut. This way I won't worry about damaging the finished 20mm diameter nor the M12x1.75 thread.


RE: Todays Project - What did you do today? - Mayhem - 03-16-2014

Thread looks fantastic from here (Dubai International Airport). I can't wait to see the next post! Thanks again!


RE: Todays Project - What did you do today? - stevec - 03-17-2014

Ken, I'm amazed that you were able to do such a beautiful job without a follower rest. Did you perhaps film a video of the operation?
( I will refrain from suggesting that when you test the screw in the nut that you thread it all the way, just in case, just kidding. Blush )


RE: Todays Project - What did you do today? - PixMan - 03-17-2014

Steve,

I had made a 52 second video of a single pass on the last attempt, when I was about halfway done. I didn't want to "jinx" it this time, just wanted to "Git 'er dun".

No fears about test fitting the screw all the way into the nut I'll make. I am quite confident that there's not more than .001" variation in thread pitch diameter.






RE: Todays Project - What did you do today? - stevec - 03-17-2014

Great Ken, your success is an obvious testament to your knowledge of and selection of cutting tools. Thumbsup


RE: Todays Project - What did you do today? - krv3000 - 03-17-2014

well dun Thumbsup


RE: Todays Project - What did you do today? - TomG - 03-17-2014

That's a good looking thread Ken. Darren will be thrilled.

Tom


RE: Todays Project - What did you do today? - f350ca - 03-17-2014

Beautiful work Ken. Sure nothing to fault on that finish.


RE: Todays Project - What did you do today? - PixMan - 03-17-2014

Thanks given to all!

It was quite a chore, probably 40 passes to get it done right. The carriage was flying. With rpm at 120 and threading feed at .200" per rev, that means 24 inches per minute rate. A little puckering every time the tool got close enough to the chuck to clear the threaded section and land in the 1/2" wide groove I made. If I had a CNC lathe like Russ, I would have run at about 500 rpm. At 120, that's only 39 surface feet per minute, far too slow for carbide inserts in most cases. Fortunately for me the threading inserts are made with a high cobalt content binder to give the insert higher toughness, a little more shear strength.

I needed that shear strength because I had smashed one corner of the insert when I engaged the half nut haphazardly and it plowed into the first thread, shearing off the insert and part of the supporting anvil. The anvil under the insert had to be changed from the standard 1.5º to a 3.5º one because of the high 2.915º lead angle of the thread.

Here's what the insert edge looked like after the first couple dozen passes, at .080" deep on the compound slide infeed:

[Image: DSC_0472-r_zps8672495a.jpg]

Indexed to a new edge, this is after finishing the thread, about .132" deep on the compound slide infeed:

[Image: DSC_0469-r_zps7acb0b28.jpg]

And a shot of the Vardex threading insert holder in it's 250-401 QCTP tool holder block:

[Image: DSC_0473-r_zpse20a0bf5.jpg]


RE: Todays Project - What did you do today? - Mayhem - 03-18-2014

(03-17-2014, 06:04 PM)TomG Wrote: ...Darren will be thrilled...

Will be? Already IS Big Grin