MetalworkingFun Forum
Todays Project - What did you do today? - Printable Version

+- MetalworkingFun Forum (http://www.metalworkingfun.com)
+-- Forum: Machining (http://www.metalworkingfun.com/forum-5.html)
+--- Forum: Projects (http://www.metalworkingfun.com/forum-7.html)
+--- Thread: Todays Project - What did you do today? (/thread-727.html)

Pages: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 500 501 502 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549 550

RE: Todays Project - What did you do today? - PixMan - 06-07-2014

Got back from Waukesha WI around midnight last night. Spent about 4 hours in the shop today trying to finish up quick small jobs.

Started by finishing the 316ss motorcycle handlebar ends Neil had roughed out. Made a steel arbor to mount them to, touched up an existing brazed carbide corner rounding tool, set the compound on the lathe to about 4-1/2º (indicator match to the existing sample), turned the tapers and radii. Then made a couple of 1-1/2" long 8mm pins with 12mm heads, showed Neil how to use an edgefinder and how to use my Albrecht sensitive drill chuck to drill the cotter/split pin holes in the pins. He made the pair of 6mm pins with 10mm heads.

We also had to drill/mill out a broken stainless steel screw from one of the two cylinders from his Yamaha RZ350 bike motor. We stripped the Kurt vise off the mill, set up an 8" precision angle iron, and strapped the sleeved aluminum water-jacketed cylinder housing to it, tipped the head of the Alliant mill to match the angle of the hole we had to fix. It looked OK with spotting it, but drilled a little off center. I used a 13/64" center cutting 4-flute solid carbide end mill to clean out the broken M6 screw. Success!

Of course without pictures none of it ever happened. Neil can vouch for me, or if you don't believe it I don't care. ;)

RE: Todays Project - What did you do today? - Mayhem - 06-07-2014

(06-07-2014, 08:33 PM)PixMan Wrote: ...Of course without pictures none of it ever happened. Neil can vouch for me, or if you don't believe it I don't care. ;)

I don't care if you don't care but I still want to see the pictures!

RE: Todays Project - What did you do today? - PixMan - 06-07-2014

Perhaps I can get Neil to post some photos. He went home with all the parts. I went home exhausted.

RE: Todays Project - What did you do today? - PixMan - 06-08-2014

Well, another day of not riding my motorcycle while it's over 80ºF, but got (hopefully) the last of the M/C parts done so I can kill the next 10 to 12 shop hours making that Kondia machine part for Darren.

If Neil needs any more, it'll be up to him to run the machines himself, though only the lathe and surface grinder will be available.

Here's two 316ss washers, Ø1.420" x Ø0.320" x 0.100" thick, with a Ø.560" x 0.030" counterbore.
[Image: IMG_20140608_140515_zpsbgpjhzdw.jpg]

And a 316ss Ø1.501 x 1.344" long disk brake piston. The original, pictured next to it, was corroded badly where the piston is exposed to the elements. That causes repeated seal failures. When I picked up the original it seemed lighter than is should be for a solid piston, yet I could see no signs of welded construction. After making the new one, I asked the customer if I could cut the old one open to see why it didn't weigh any more than the one I made with a Ø1-1/8" x 1-1/8" deep bore.

After cutting into it with a Kennametal 3/4" 3-insert should mill, the "cover" popped out, jammed and busted an insert. I should be able to fix the cutter, but damaging the cutter for the sake of curiosity wasn't worth it. Hindsight is 20/20.

[Image: IMG_20140608_144936897_zpsanoxrh3i.jpg]
[Image: IMG_20140608_145007767_zpsglul53ni.jpg]

Neil has some photos of yesterday's work. He said he'd post them later.

RE: Todays Project - What did you do today? - f350ca - 06-10-2014

Spent a couple of evenings with my son machining a stem for his bike. A piece of mystery metal from an aircraft plant, hard enough it rings when you tap it. Nice stuff to machine.

[Image: _MG_4483.jpg]

[Image: _MG_4485.jpg]

RE: Todays Project - What did you do today? - PixMan - 06-10-2014

Looks nice! Probably 7075 aluminum.

RE: Todays Project - What did you do today? - TomG - 06-10-2014

I've machined quite a bit of aluminum for aircraft work and if it was nice to machine, it was likely 2024-T351. It cuts easily and unlike 6061, the chips actually break.

Tom

RE: Todays Project - What did you do today? - Mayhem - 06-14-2014

Simple little job for my Mum today. The plastic (?Bakelite) ball on her wood burning stove fell off. The threads stripped out. I tuned down a 9.9mm shaft and drilled and threaded the 5/16-18 to fit the lever. Knurled the outside and pressed it into a 10mm hole with some high strength Loc-Tite.

[attachment=8600]
[attachment=8601]
[attachment=8602]

RE: Todays Project - What did you do today? - DaveH - 06-14-2014

Nicely done - perfect Thumbsup
Smiley-eatdrink004
DaveH

RE: Todays Project - What did you do today? - Hawkeye - 06-15-2014

I decided to try to make a mist coolant gizmo, loosely based on some I've seen on the internet. The main push for this was getting a flood coolant nozzle with magnetic base through the local tool store.

Some that I've seen use two pressure regulators. One for the air flow at the nozzle, one to pressurize the liquid supply bottle. I decided to try using just one, mostly because I didn't buy a second one when it was on sale recently. Mine uses one regulator to adjust the air flow through the nozzle, with that pressure also entering the bottle to push the coolant out. The tube coming vertically out of the brass fitting carries the liquid to the nozzle.
[attachment=8620]

Rather than mix air and coolant before they go down the flexible tube to the nozzle, I ran a thin nylon tube down the middle of the flex to carry coolant to the nozzle itself. I filed three notches around the opening of the original nozzle to allow good air flow out past the thin tube. There is also an insert made from 1/16" O.D. brass tubing in the end of the tube to restrict the flow.
[attachment=8621]

I made up an aluminum block to allow mounting of the flex tube and connect the air and coolant lines. In my first attempt, I used the valve that came with the nozzle assembly. Leaked like a sieve. The screw on the top of the fitting is a needle valve I made from a bolt, to regulate the amount of coolant coming out.
[attachment=8622]

Today, I picked up a small needle valve at the hardware store and reworked the regulator stage. Now there are no leaks and I can turn the coolant flow as low as I want.
[attachment=8623]

I haven't tried machining with it yet. I'm going to work out a better method of hanging the supply bottle so the rig can be easily moved from machine to machine. Reports from other builders indicate that coolant usage is quite low. I'm using a semi-synthetic water-soluble oil for my first trials.