MetalworkingFun Forum
Todays Project - What did you do today? - Printable Version

+- MetalworkingFun Forum (http://www.metalworkingfun.com)
+-- Forum: Machining (http://www.metalworkingfun.com/forum-5.html)
+--- Forum: Projects (http://www.metalworkingfun.com/forum-7.html)
+--- Thread: Todays Project - What did you do today? (/thread-727.html)

Pages: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 500 501 502 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549


RE: Todays Project - What did you do today? - the penguin - 03-04-2018

Tom,

This saw was sold by Rockwell/Delta as either a wood or metal cutting bandsaw, I bought the saw used, from my wife’s uncle, a retired GM executive, so he bought all of the attachments. As I stated earlier, I have zero interest in anything involving wood, so I’ve have it set up for metal cutting, with the saw speed at the slowest rate.

I have the original manual explaining the gear mechanism that the knob, engages/disengages, depending on where it’s turned to.

When I got the saw, it had a broken locking pin, in the mechanism, so about 12-15 years ago, I had the whole drive mechanism completely apart.


RE: Todays Project - What did you do today? - TomG - 03-07-2018

I finally got the hi/low drive system functional on the old Delta bandsaw. It required an 8" pulley and a 60" belt  for the high range, plus a hinged belt tensioner for the motor. I doesn't appear that there ever was one, but how they got by without one is beyond me. I also had to make some spacers to raise the saw and make room for the tensioner, and consequently relocate the position of the belt guard. It took more effort than anticipated, but it sure is nice to finally have five speeds. Thumbsup

Tom

[Image: 20180307_2004481.jpg]


RE: Todays Project - What did you do today? - Highpower - 03-07-2018

Smiley-signs107

Tom, why is there a flat on the top of the rear cover? I'm just curious if there is a particular reason for having that when the top of the front cover is rounded?


RE: Todays Project - What did you do today? - f350ca - 03-07-2018

I looked through all the literature I could find on that saw and never figured how they tensioned the belt. The base has slots front to back for the motor but that wouldn't adjust the tension. In the end made a hinged mount like yours.


RE: Todays Project - What did you do today? - TomG - 03-07-2018

(03-07-2018, 08:28 PM)Highpower Wrote: Smiley-signs107

Tom, why is there a flat on the top of the rear cover? I'm just curious if there is a particular reason for having that when the top of the front cover is rounded?

No idea Willie. It is factory though, so the Rockwell designers must have had a reason. Chin

Tom


RE: Todays Project - What did you do today? - TomG - 03-16-2018

I finished up the fence for my bandsaw today. It's been a while since I've done any extensive machining on steel and it seemed to take FOREVER. Definitely followed some of my own advice and plunge milled as much as I could. The design is basically a copy (from memory) of a fence on a DoAll saw that I used to use. It's short enough that it can be used close to the blade and rock solid, even though it only clamps on one end. Can't wait to try it out.

Tom


[Image: 20180316_202315.jpg]


RE: Todays Project - What did you do today? - EdK - 03-16-2018

Very nice Tom! Thumbsup

I'm sure it'll work just fine.

Ed


RE: Todays Project - What did you do today? - Hawkeye - 03-16-2018

Tom, one thing I've found with bandsaws is that every blade tends to pull to one side when using a fence. It helps to have a fence that can be adjusted to an angle that lets the blade cut parallel to the fence. Even when cutting metal, the fence can be set by cutting wood.

You cut in a few inches along the fence, then measure the piece. If it isn't parallel, you adjust the angle and take another cut in a fresh part of the wood. Repeat until the cut comes out parallel. Then it should be good until you replace the blade or something damages the blade.


RE: Todays Project - What did you do today? - TomG - 03-16-2018

Thanks Mike, I'll keep that in mind. It wouldn't take much to add and adjustment.

Tom


RE: Todays Project - What did you do today? - TomG - 04-08-2018

I tied my hand at upholstering today and got a good start on reupholstering the seats in the Rambler. The cloth on the old ones and the sunny side of the vinyl was literally falling apart. I opted for black vinyl with pleats and neon green top stitching to compliment the future paint color. The rear bench went pretty slow because I had to decide how to mark everything in a way that I could remember how to put it back together. I also took a ton of pics as it came apart just to be safe. The line laser guide I made for the sewing machine worked great on the top stitching. I just placed the line on the seam with the proper offset and sewed away. For the most part, they came out reasonably straight for an amateur. :)

Tom

[Image: 20180405_160319.jpg]

[Image: 20180405_191837.jpg]

[Image: 20180405_193742.jpg]

[Image: 20180406_193640.jpg]

[Image: 20180406_193733.jpg]

[Image: 20180406_200532.jpg]

[Image: 20180406_204341.jpg]

[Image: 20180407_100854.jpg]

[Image: 20180408_163011.jpg]