Metal gears for 7x12s
#1
I want to change the plastic gears on my Red Bull (Chester Conquest) for metal ones. before the 1hp motor has them for breakfast.Smiley-dancenana
The only ones i can find are for Sieg lathes ,can anyone tell me if they will fit.
BrianChin
Brian, proud to be a member of MetalworkingFun since Sep 2012.
http://briansworkshop.weebly.com Welcome
Reply
Thanks given by:
#2
I would call Littlemachineshop.com and talk to them.

http://www.littlemachineshop.com/product...7&category=

Ed
Reply
Thanks given by:
#3
C'mon Brian, you, of all people, won't cut your own? It's just a little "minimal gear cutting" Rotfl
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Reply
Thanks given by:
#4
JMO, but i think some of those lathes/mills with "ONE" plastic gear is kind of a good idea as a safety, like a shear pin , if it happens.
sasquatch, proud to be a member of MetalworkingFun since Jul 2012.
Reply
Thanks given by:
#5
(03-15-2013, 11:43 AM)Brian Wrote: I want to change the plastic gears on my Red Bull (Chester Conquest) for metal ones. before the 1hp motor has them for breakfast.Smiley-dancenana
The only ones i can find are for Sieg lathes ,can anyone tell me if they will fit.
BrianChin

Brian,

Are you having problems with the plastic gears? I have a HF 7x10 that I've had for about 13 years, it was my very first metal lathe, and it has the plastic gears. I've never had a problem with them at all.

Ed
Reply
Thanks given by:
#6
(03-15-2013, 06:51 PM)sasquatch Wrote: JMO, but i think some of those lathes/mills with "ONE" plastic gear is kind of a good idea as a safety, like a shear pin , if it happens.

JMO??
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Reply
Thanks given by:
#7
(03-15-2013, 07:16 PM)stevec Wrote:
(03-15-2013, 06:51 PM)sasquatch Wrote: JMO, but i think some of those lathes/mills with "ONE" plastic gear is kind of a good idea as a safety, like a shear pin , if it happens.

JMO??

I think that would be "just my opinion", but that's just a guess. 17428

Ed
Reply
Thanks given by:
#8
here's a link to stock drive products which is were I would them from you may have to pay more, but you will get a lot higher quality of gear.


http://www.sdp-si.com/eStore/CoverPg/Gears.htm

I have one of the HF 7X12 lathes which I changed the plastic gears in the head to metal ones because I had them from when my mini mill was gear driven.
actually any place that you can buy Module 1 gears from will have the gears you need to swap.

DA
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.

If life seems normal, your not going fast enough! Tongue
Reply
Thanks given by:
#9
JMO, Yup, just my opinion,, which at times is about equal to the round number below one.


HOWEVER,, I,m sticking to it!! Lol
sasquatch, proud to be a member of MetalworkingFun since Jul 2012.
Reply
Thanks given by:
#10
(03-16-2013, 07:56 PM)sasquatch Wrote: JMO, Yup, just my opinion,, which at times is about equal to the round number below one.


HOWEVER,, I,m sticking to it!! Lol

I lke the idea of one plastic gear if its the one on the lay shaft its easy to replace. No Need to remove the spindle, and low cost replacements,
may also be quieter than 2 metal gears.6799

Brian.Smile
Brian, proud to be a member of MetalworkingFun since Sep 2012.
http://briansworkshop.weebly.com Welcome
Reply
Thanks given by:




Users browsing this thread: 1 Guest(s)