drip oilers
#31
A very nice job, David Smiley-signs107
Smiley-eatdrink004
DaveH
Reply
Thanks given by:
#32
(12-15-2013, 06:57 PM)DaveH Wrote: A very nice job, David Smiley-signs107
Smiley-eatdrink004
DaveH

Thanks, I still have a couple little things left to do but basically they are finished

DA
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.

If life seems normal, your not going fast enough! Tongue
Reply
Thanks given by:
#33
They turned out great, love the look of drill oilers, very classy.
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:
#34
(12-15-2013, 08:16 PM)f350ca Wrote: They turned out great, love the look of drill oilers


When I made mine I used plastic pill containers. I didnt even cut the
bottom, just a large hole and used '0' rings. I used lawnmower carb.
jets for the drip. They work.


Edit: to fix quote tags
big job, proud to be a member of MetalworkingFun since Jun 2012.
Reply
Thanks given by:
#35
was easier for me to copy the small one that I had been given then to re-engineer them. lot of people said to use plastic but I wanted glass for the look, plus the tubes were pretty cheap.
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.

If life seems normal, your not going fast enough! Tongue
Reply
Thanks given by:
#36
(11-09-2013, 11:17 AM)dallen Wrote:
(11-09-2013, 09:55 AM)EdK Wrote: Nice job on the form tool David. Thumbsup

Ed

it should of been flat on top with no rake, but the bit was one that I had already used for something else and the side I turned up only had a slight negitive rake on it. It actually cut pretty good, I had it on center and would crank the cross slide in about 10 15 thousands and then run the carriage into the part to the depth that I needed, using lots of dark cutting oil.


(11-09-2013, 10:51 AM)DaveH Wrote: Coming a long nicely Thumbsup
Smiley-eatdrink004
DaveH

Dave, I've reached the point of needing the glass tube's, or I may just use some stainless steel tubing I have so I can call them done till I get the glass. They have actually been a lot easier to make then I had first thought they would be.

The one part that I haven't really figured out is the little cover over the filler hole as its spring loaded I may just put in a tube with a drop cap on it and a little chain or something to keep them from getting misplaced.

If you need to buy oiler glass, this is a real good source.
http://www.enginads.com/starbolt/
South Bend lathe
Bridgeport mill
Powermatic drill press
Wellsaw model 8 bandsaw
Reply
Thanks given by:
#37
can't remember if I posted photo of where I am at with the oiler project or not so I'll stick one on here.

Cast Iron I already have the glass but thanks for the info. I need one of the little sight glasses to replace one I cracked.

[Image: with-oil.jpg]
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.

If life seems normal, your not going fast enough! Tongue
Reply
Thanks given by:
#38
Dave,I betcha you would'nt have cracked a plastic sight "glass". Big Grin
Sorry, Blush
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Reply
Thanks given by:
#39
Steve I betcha the glass ones don't discolor like most plastic's do Big GrinBig Grin
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.

If life seems normal, your not going fast enough! Tongue
Reply
Thanks given by:
#40
(12-26-2013, 10:30 AM)dallen Wrote: Steve I betcha the glass ones don't discolor like most plastic's do Big GrinBig Grin

Or get as scratched or "fogged". Big Grin

Nicely done Dallen.

-Ron
11" South Bend lathe - Wells-Index 860C mill - 16" Queen City Shaper
Reply
Thanks given by:




Users browsing this thread: 1 Guest(s)