Posts: 4,438
Threads: 183
Joined: Feb 2012
Location: Missouri, USA
Mayhem,
Any idea of how much amperage that was pulling on average?
And I'm assuming a 12 volt charger?
It sure looks like it did the trick!
By the way..... NICE PICTURES!
Willie
Posts: 4,683
Threads: 93
Joined: Feb 2012
Location: Perth, Australia
05-06-2012, 01:06 AM
(This post was last modified: 05-06-2012, 01:10 AM by Mayhem.)
The charger is an old one that is capable of charging up to six 6V batteries at one time. It will also charge 12V batteries. I have never bothered to meter the output. I just recall seeing a plate that mentioned the six battery ability. Come to think about it, none of the knobs are marked. I usually just move them until I see a decent current draw on the meter.
Initial draw was a little over 6A but this reduced to about 4A after about an hour or so.
Hunting American dentists since 2015.
Nicely shown Mayhem
great shot of the crud
Your are actually Electrolytic Cleaning ,, and its the rapid production of Hydrogen gas at the surface of the Cathode that dose the cleaning .
The more amps you can get into the job the better ,, actually 6v to 12v with a current density of 10amps./ sq ft .
Rob
Just remember that's HYDROGEN gas is being produced . ( BOOM )
Ed blown up smile needed
Posts: 2,685
Threads: 29
Joined: Feb 2012
Location: Nova Scotia, Canada
Baking soda you say? I thought it had to be washing soda like the Arm & Hammer stuff. Guess not.
Don't try it with one of the newer chargers that electronically control the charge rate, they don't output power until they sense the power in the battery to be charged. (I wonder if they won't charge a DEAD battery for that reason?)
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Posts: 4,513
Threads: 139
Joined: Feb 2012
Location: Kempton Park. South Africa
05-06-2012, 10:15 AM
(This post was last modified: 05-06-2012, 10:15 AM by DaveH.)
Mayhem,
That is quite impressive, just to be sure the "work piece" is connected to the negative.
Is that correct?
DaveH
Posts: 4,438
Threads: 183
Joined: Feb 2012
Location: Missouri, USA
(05-06-2012, 04:43 AM)RobWilson Wrote: Just remember that's HYDROGEN gas is being produced . ( BOOM )
Ed blown up smile needed
Fixed that for you....
Willie
Cheers Willie ,,,,,,,,,, me like
Rob
(05-06-2012, 10:04 AM)stevec Wrote: Baking soda you say? I thought it had to be washing soda like the Arm & Hammer stuff. Guess not.
Don't try it with one of the newer chargers that electronically control the charge rate, they don't output power until they sense the power in the battery to be charged. (I wonder if they won't charge a DEAD battery for that reason?)
Hi Steve ,,,,,,,,,, any Alkali or Alkaline salt will do the job .Sodium Bicarbonate and Sodium Carbonate are both Alkaline .Sodium Carbonate being more Alkaline than Sodium Bicarbonate .
Yep ,,,,,,, the newer electronic battery charger are a pain in the butt , the battery needs to have at least some voltage for the charger electronics to register that it is actually connected to a battery before it will charge , older chargers were fitted with an over discharge button so you could charge a dead flat battery .
Finished waffling now Rob
Posts: 2,685
Threads: 29
Joined: Feb 2012
Location: Nova Scotia, Canada
Rob, do you put treakle on your waffles?
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Posts: 126
Threads: 23
Joined: Apr 2012
Location: houston pa
a bit off topic but if you have a battery that the charger wont recognize you can hook a good battery to the dead one to get the charger to pick it up and it will start charging it. most likely at that point its already catastrophically sulfated or dead celled recycle material but it doesn't cost much to try.
mikecwik, proud to be a member of MetalworkingFun Forum since Apr 2012.
|