Setting Up My PM935 Mill
You just need some lipstick Ed. Smile

http://www.todayshomeowner.com/video/cut...let-boxes/

Smiley-eatdrink004 
DaveH
Reply
Thanks given by:
(10-19-2015, 06:50 PM)DaveH Wrote: You just need some lipstick Ed. Smile

http://www.todayshomeowner.com/video/cut...let-boxes/

Smiley-eatdrink004 
DaveH

That's an old trick from way back that I've used before. I prefer to use chalk though since I have chalk but I ran out of lipstick.  Yikes

And, that doesn't work when you've got outlets installed already and there's no way in hell I'm going to take them out. They were a bugger to install. 12 gauge wire is a pain to work with compared to 14 gauge.

Ed
Reply
Thanks given by:
(10-18-2015, 09:34 AM)wawoodman Wrote: Not exactly what you're looking for, but it might help:

https://www.fastcap.com/estore/pc/Electr...3p2478.htm

Thanks for the link. I also think their outlet making stamp looks like a great ideal.
Reply
Thanks given by:
(10-19-2015, 06:55 PM)EdK Wrote:
(10-19-2015, 06:50 PM)DaveH Wrote: You just need some lipstick Ed. Smile

http://www.todayshomeowner.com/video/cut...let-boxes/

Smiley-eatdrink004 
DaveH

That's an old trick from way back that I've used before. I prefer to use chalk though since I have chalk but I ran out of lipstick.  Yikes

And, that doesn't work when you've got outlets installed already and there's no way in hell I'm going to take them out. They were a bugger to install. 12 gauge wire is a pain to work with compared to 14 gauge.

Ed

That's why I did all the wiring here in pipe and used stranded #12.
Logan 200, Index 40H Mill, Boyer-Shultz 612 Surface Grinder, HF 4x6 Bandsaw, a shear with no name, ...
the nobucks boutique etsy shop  |  the nobucks boutique
Reply
Thanks given by:
Conduit is a wonderful thing!
Reply
Thanks given by:
Change of plans, literally. I rearranged the floor plan, again. This will allow access to the back of the lathe since the electrical box and motor are back there. After I install the VFD and 3-phase motor on the lathe, the electrical box will get relocated to the wall to the right of the lathe.
This rearrangement also gets the shelves inside the shop space and moves the desk out where it's less likely to be bombarded with swarf. Of course this means the duplex outlet I installed now has to come out and relocated.  Bash  I'm sure glad I didn't drive home the nails on the piece of luan plywood I installed on the wall. I left the heads proud of the surface just in case this would change.

So back to square one, I guess.  Smiley-signs125

I like this layout better so it's worth the work to change it.

Ed

   
Reply
Thanks given by:
Looks good Ed, but where is the fridge? Smiley-eatdrink004

Be sure to put up plenty of light over the machines. If you think you have enough, add more.

Tom
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by: EdK
(10-24-2015, 12:17 PM)TomG Wrote: Looks good Ed, but where is the fridge? Smiley-eatdrink004

Be sure to put up plenty of light over the machines. If you think you have enough, add more.

Tom

Thanks Tom. Right now I have a 4ft florescent light directly over my lathe and an incandescent goose-neck task light attached to the back splash. I'll be adding probably three more florescent light fixtures to the shop area and then I need to figure out what I'm going to use for task lighting on the mill. I like the goose-neck lights with the real long goose necks so I'll probably get a couple of those for the mill.
Oh, and I'll fit a fridge in there somewhere, possibly underneath the work bench.

Ed
Reply
Thanks given by:
(10-24-2015, 11:21 AM)EdK Wrote: Of course this means the duplex outlet I installed now has to come out and relocated.  Bash  

Ed

Or simply remember that there is an outlet behind "all that stuff" that you can not get to with the current configuration but will be very handy and show what a forward thinker you are when you decide to change things around again.

That's how I'd [have actually] rationalize it  Smile

Arvid
Reply
Thanks given by:
(10-24-2015, 01:32 PM)arvidj Wrote:
(10-24-2015, 11:21 AM)EdK Wrote: Of course this means the duplex outlet I installed now has to come out and relocated.  Bash  

Ed

Or simply remember that there is an outlet behind "all that stuff" that you can not get to with the current configuration but will be very handy and show what a forward thinker you are when you decide to change things around again.

That's how I'd [have actually] rationalize it  Smile

Arvid

I'm liking that idea. Less work. Thumbsup

Ed
Reply
Thanks given by:




Users browsing this thread: 59 Guest(s)