MetalworkingFun Forum › Machinery › Milling Machines v
Setting Up My PM935 Mill

Thread Modes
Setting Up My PM935 Mill
Vinny Online
Another Whipping Boy
*******
Posts: 2,608
Threads: 99
Joined: Dec 2014
Location: Michigan
#211
11-15-2015, 07:47 PM
Steel Dave.
Logan 200, Index 40H Mill, Boyer-Shultz 612 Surface Grinder, HF 4x6 Bandsaw, a shear with no name, ...
the nobucks boutique etsy shop  |  the nobucks boutique
Website
Reply
Thanks given by: DaveH
DaveH Offline
Child of the 60's
******
Posts: 4,513
Threads: 139
Joined: Feb 2012
Location: Kempton Park. South Africa
#212
11-16-2015, 02:27 PM
Thanks Vinny, I just wondered - my house is all done in conduit (plastic).
Smiley-eatdrink004 
DaveH
 a child of the 60's and 50's and a bit of the 40's Smile
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,842
Threads: 318
Joined: Feb 2012
Location: Arizona/Minnesota
#213
11-26-2015, 04:16 PM
The first piece is finally down the basement.

I have a question about removing the head. Is anyone familiar with the step pulley Bridgeport mill? I want to remove the head next and I'm thinking I can just remove the four bolts on the front and slide the head forward to remove it. Is that true or is there more to it?

Ed

         


   
Reply
Thanks given by:
TomG Offline
Alt. Whipping Boy
*******
Posts: 3,798
Threads: 184
Joined: Jun 2012
Location: Farmington Hills, Michigan
#214
11-26-2015, 06:22 PM
That's all there is to it Ed, except that it is surprisingly heavy. Do you have a lift?

Tom
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,842
Threads: 318
Joined: Feb 2012
Location: Arizona/Minnesota
#215
11-26-2015, 07:27 PM
(11-26-2015, 06:22 PM)TomG Wrote: That's all there is to it Ed, except that it is surprisingly heavy. Do you have a lift?

Tom

Thanks Tom. Yes, I have a cherry picker. How to grab on to the head is going to be tricky but I'll figure something out.

Ed
Reply
Thanks given by:
Highpower Offline
JAFO
******
Posts: 4,438
Threads: 183
Joined: Feb 2012
Location: Missouri, USA
#216
11-27-2015, 12:15 PM
Just be mindful of the bevel gear and worm behind the head. Try to keep the head level and come straight out with it so it's not flopping around like a fish. Smile
Willie
Reply
Thanks given by: EdK
Sunset Machine Offline
Junior
****
Posts: 716
Threads: 32
Joined: Apr 2012
Location: Washington, USA
#217
11-27-2015, 01:45 PM
Maybe like the shipping position, upside down and on a small wood pallet that you can sling with the hoist?
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,842
Threads: 318
Joined: Feb 2012
Location: Arizona/Minnesota
#218
11-27-2015, 04:51 PM
(11-27-2015, 01:45 PM)Sunset Machine Wrote: Maybe like the shipping position, upside down and on a small wood pallet that you can sling with the hoist?

Hmmm, that's a good thought. Chin

Ed
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,842
Threads: 318
Joined: Feb 2012
Location: Arizona/Minnesota
#219
11-27-2015, 06:55 PM
It was cold out in the garage today so I got a heater to help take the chill out of the air. I got the cherry picker up into the garage and all assembled so it's ready to do its job. I think I have a plan for getting the head off. It's supposed to be in the 30s F tomorrow so it will be more tolerable than it was today. Hopefully I'll get the head and ram off tomorrow without incident. Sweat

Ed
Reply
Thanks given by:
f350ca Offline
Senior
*****
Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario
#220
11-27-2015, 07:49 PM
Set up the way you have it in the last photo Ed, with the head sitting on the table. You should be able to hook up the hoist to stabilize it and retract the arm on the column till the studs are clear.
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:




Users browsing this thread: 18 Guest(s)