Posts: 8,842
Threads: 318
Joined: Feb 2012
Location: Arizona/Minnesota
The following 1 user Likes EdK's post:
arvidj (12-30-2015)
(12-30-2015, 04:12 PM)arvidj Wrote: I'm sure you have a plan detailing how you will get the spider back up to the top and hold it there while you attach at least on bolt thru the turret.
Just wondering ...
For once, I actually do Arvid. Side access panel.
Ed
Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario
The following 1 user Likes f350ca's post:
EdK (12-30-2015)
That looks like a two person job!
The spider on mine sat there when I lifted the ram to add a riser, which is still there due to laziness. But then again its stored where I can find it.
Free advice is worth exactly what you payed for it.
Greg
Posts: 4,438
Threads: 183
Joined: Feb 2012
Location: Missouri, USA
When I removed the knee from mine I was by my lonesome. I cranked the knee all the way up until the screw was just sitting on top of the bronze nut. (Still plenty of dovetail left to hold it in place.) Put a couple of lifting straps through it and hooked up to the cherry picker to take the weight off of the screw/nut. I removed the jib (didn't want to break it) and lifted the knee straight up off of the dovetails. Re-installed it in reverse order (again by myself). Just had to guide the knee into position with one hand and operate the cherry picker with the other.
Willie
Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario
I meant putting that spider back in Willie, can see me trying to hold that up through the opening and drop the bolts in from above.
Free advice is worth exactly what you payed for it.
Greg
Posts: 8,842
Threads: 318
Joined: Feb 2012
Location: Arizona/Minnesota
(12-30-2015, 06:00 PM)f350ca Wrote: That looks like a two person job!
The spider on mine sat there when I lifted the ram to add a riser, which is still there due to laziness. But then again its stored where I can find it.
Well, I have me, myself and I so I think I've got that covered.
Ed
Posts: 2,608
Threads: 99
Joined: Dec 2014
Location: Michigan
Well hells's bells Ed. That's three of ya, you should have no problem!!
Posts: 8,842
Threads: 318
Joined: Feb 2012
Location: Arizona/Minnesota
(12-30-2015, 06:56 PM)Highpower Wrote: When I removed the knee from mine I was by my lonesome. I cranked the knee all the way up until the screw was just sitting on top of the bronze nut. (Still plenty of dovetail left to hold it in place.) Put a couple of lifting straps through it and hooked up to the cherry picker to take the weight off of the screw/nut. I removed the jib (didn't want to break it) and lifted the knee straight up off of the dovetails. Re-installed it in reverse order (again by myself). Just had to guide the knee into position with one hand and operate the cherry picker with the other.
Willie,
So there's no mechanism to prevent cranking it all the way off of the screw by mistake? I think the Bridgeport mills have something to prevent that. At least that's what it sounded like based on some info My Google found for me.
Ed
Posts: 4,438
Threads: 183
Joined: Feb 2012
Location: Missouri, USA
On my mill there is a stop pin/bolt on the column that keeps the knee from traveling too high when it's in place. But after the pin is removed the knee will crank farther up until knee elevation screw comes out of the nut.
But you're right, a real Bridgy is probably different so I'll shut up now.
Willie