Posts: 2,608
Threads: 99
Joined: Dec 2014
Location: Michigan
The strap is only holding onto the casting? Or is there something inside it goes around?
Posts: 8,842
Threads: 318
Joined: Feb 2012
Location: Arizona/Minnesota
(02-09-2016, 05:55 PM)Mayhem Wrote: Personally - I would go ahead with the setup you describe. It isn't all that much weight (based on my Kondia experience) and you are only talking about a minute or so in duration.
That's my gut feeling too. I'll have a tether tied higher up just to stabilize it to keep it from tipping over since it's rather top heavy.
Ed
Posts: 8,842
Threads: 318
Joined: Feb 2012
Location: Arizona/Minnesota
(02-09-2016, 05:55 PM)Vinny Wrote: The strap is only holding onto the casting? Or is there something inside it goes around?
Just the casting.
Ed
Posts: 4,438
Threads: 183
Joined: Feb 2012
Location: Missouri, USA
(02-09-2016, 05:39 PM)EdK Wrote: You guys think the casting is strong enough to take the weight of the head as it's lowered down the planks to the basement?
Ed
I agree with Darren and think you would be OK Ed. But you could also cut a piece of 4x4 to stick into the motor opening between your pallet and the bottom of the casting (now UP) to spread some of the load to the solid bottom of the casting. Cheap insurance and it might make you feel a little better about it.
Willie
Posts: 2,608
Threads: 99
Joined: Dec 2014
Location: Michigan
(02-09-2016, 06:26 PM)EdK Wrote: (02-09-2016, 05:55 PM)Vinny Wrote: The strap is only holding onto the casting? Or is there something inside it goes around?
Just the casting.
Ed
Just the casting makes me nervous. Casting and sled I'd be more comfortable. Something to spread it out.
Posts: 8,842
Threads: 318
Joined: Feb 2012
Location: Arizona/Minnesota
(02-09-2016, 10:18 PM)Highpower Wrote: But you could also cut a piece of 4x4 to stick into the motor opening between your pallet and the bottom of the casting (now UP) to spread some of the load to the solid bottom of the casting.
Willie,
That's a picture of the head sitting on the mill table. The head is fully supported on the bottom side by the sled.
Ed
Posts: 4,438
Threads: 183
Joined: Feb 2012
Location: Missouri, USA
Yes, I got that part Ed. It's supported on the bottom where the thin sections are between the openings for the motor and spindle pulleys. I was just talking about putting a block of wood INSIDE the motor opening and adding some support to filled in area of the red box of this beautiful artists rendition.
p.s.
I wrote pallet where you called it a sled. Same difference.
But it would probably take you an hour to undo all of your bondage work anyway, so you might as well go for it as-is.
Willie
Posts: 8,842
Threads: 318
Joined: Feb 2012
Location: Arizona/Minnesota
The following 1 user Likes EdK's post:
Highpower (02-10-2016)
(02-10-2016, 08:45 AM)Highpower Wrote: But it would probably take you an hour to undo all of your bondage work anyway, so you might as well go for it as-is.
Yup, I really didn't want to have to redo the bondage accoutrements. I'm lazy and I may pay for that disgression. But I'm not done bondagizing it yet.
Ed
Posts: 2,608
Threads: 99
Joined: Dec 2014
Location: Michigan
"bondagizing" ?? Well that's a new one.
Posts: 4,438
Threads: 183
Joined: Feb 2012
Location: Missouri, USA
(02-10-2016, 06:11 PM)Vinny Wrote: "bondagizing" ?? Well that's a new one.
The scary thing is, if you Google it you'll actually get a hit...
Willie