Todays Project - What did you do today?
Can't post multiple images so here is one more as I know you all like a pictures.

   
Reply
Thanks given by:
(10-10-2016, 07:05 AM)Mayhem Wrote: I'm guessing the set screw is ensuring that the bolt on the left is locking the gib.  If so, is there any need for the pivot and link arm.  Or is this preventing gravity unlocking it?

Possibly both screws are being tightened at the same time? That would explain the link. Chin
Willie
Reply
Thanks given by:
you got it . both the bolts that screw into the casting are pushing agianst the gib they only need half a turn or less to be tight or loose the link lets you snug them both at the same time and it replaces 2 little toggles the used to be there . and adjusting those little toggle bolts always guarantees a black greasey mark on the back of your hand .
texx, proud to be a member of MetalworkingFun Forum since May 2014.
Reply
Thanks given by:
(10-10-2016, 02:07 PM)Old Minger Wrote: Can't post multiple images so here is one more as I know you all like a pictures.

You should be able to post multiple attachments to your posts. What sort of problem did you have trying to do it?

Ed
Reply
Thanks given by:
(10-10-2016, 03:41 PM)texx Wrote: you got it . both the bolts that screw into the casting are pushing agianst the gib they only need half a turn or less to be tight or loose the link lets you snug them both at the same time and it replaces 2 little toggles the used to be there . and adjusting those little toggle bolts always guarantees a black greasey mark on the back of your hand .

Now it makes sense.
Logan 200, Index 40H Mill, Boyer-Shultz 612 Surface Grinder, HF 4x6 Bandsaw, a shear with no name, ...
the nobucks boutique etsy shop  |  the nobucks boutique
Reply
Thanks given by:
(10-10-2016, 05:13 PM)EdK Wrote:
(10-10-2016, 02:07 PM)Old Minger Wrote: Can't post multiple images so here is one more as I know you all like a pictures.

You should be able to post multiple attachments to your posts. What sort of problem did you have trying to do it?

Ed

Quick answer as i known this is not the right place for this issue.
When adding an additional attachment ie second image, I get an error message saying image  has the same file name as previous image. This is not the case so I have to include only 1 image per posting.
I had a whole Bridgeport restoration thread planned put with this posting of images issue I have I think I will Pass.
Reply
Thanks given by:
Vinny and Mayhem,

On these machines, there are two screws that apply pressure to the gib in order to lock the Y-axis. As they come from the factory, you have to tighten both to lock the table. The two arms joined by the horizontal link turn both of the new bolts at the same time, applying locking pressure that is better than the original arrangement.
Mike

If you can't get one, make one.

Hawkeye, proud to be a member of MetalworkingFun Forum since Jan 2013.
Reply
Thanks given by:
Thanks Mike - the absence of a visible set screw on the rear bolt threw me.
Hunting American dentists since 2015.
Reply
Thanks given by:
(10-10-2016, 02:07 PM)Old Minger Wrote: Can't post multiple images so here is one more as I know you all like a pictures.

Try uploading your pics to Photobucket and then copying them to your post.
Reply
Thanks given by:
I'm getting down on the old project list, so now I'm ticking off the little ones I've been leaving for some time. Yesterday, I finally got a stock support built for the horizontal bandsaw. I picked up a pair of small rollers at Restore last year and dug a 1" thick disk out of stock. That's as far as I got back then. Simple enough. Weld a small disk on a 3/4" nut, weld a piece of 3/4" pipe to the base, attach the roller to the threaded rod. Done and used twice already.
   

The second item off the list was a simple stop for the 6" vise I picked up last summer for the Victoria mill. The small block behind the stop is what I cut out with bandsaws to save a LOT of milling.
   
Mike

If you can't get one, make one.

Hawkeye, proud to be a member of MetalworkingFun Forum since Jan 2013.
Reply
Thanks given by:




Users browsing this thread: 35 Guest(s)