01-08-2021, 10:43 AM
No doubt about it, Wiha is good stuff. I have a set of their small nut drivers & they're very well made.
Ed
Ed
Latest Delivery
|
01-08-2021, 10:43 AM
No doubt about it, Wiha is good stuff. I have a set of their small nut drivers & they're very well made.
Ed
01-08-2021, 03:08 PM
Totally agree. I was tired of re-buying the cheaply made 5-6 piece miniature screwdriver sets every year when the ends twisted or broke trying to remove tight screws. I got the bench top set from Wiha a couple years ago and the difference has been night and day.
Oddly enough I seem to prefer the Wera brand over Wiha for standard size (insulated) screwdrivers though. ¯\_(ツ)_/¯
Willie
02-12-2021, 04:37 PM
Willie
02-12-2021, 05:14 PM
02-12-2021, 08:47 PM
(02-12-2021, 05:14 PM)TomG Wrote:(02-12-2021, 04:37 PM)Highpower Wrote: New arrival. Just a small end mill extension (1/2" x 5") and 2 collets. ($$$) I have a handful of regular (short) end mill holders (Enco) but have snapped carbide tools a bit too easily using them in the past. I haven't checked the run out on them but the bores seem to be a tight fit. Still I don't like the feeling of cranking down set screws against a carbide shank to hold a tool in place. Harvey claims a maximum T.I.R. of .0002" from shank to collet pocket on these extensions. Since I want to be able to get down into some deep pockets/cavities I figured the collet setup would be my best chance of getting 1/8" carbide ends mills to survive. My 1/8" end mill holder is now dedicated for a spotting drill bit. No more side milling - with carbide anyway.
Willie
03-26-2021, 08:42 PM
Not sure where this fits most, here or electronics, but I have already used it in on something I'm machining so I guess this works. I had one of these at work that I used for years and finally got one here. I mounted it to a scrap piece of corian I had layin around and put some stick on rubber feet on the bottom. This was a $25 ebay find.
Logan 200, Index 40H Mill, Boyer-Shultz 612 Surface Grinder, HF 4x6 Bandsaw, a shear with no name, ...
the nobucks boutique etsy shop | the nobucks boutique
03-27-2021, 12:26 AM
They are quite handy. I have one and a set of Panavise's helping hands that are excellent when trying to solder fine wires. My late wife also used it when working on small sculptures.
03-27-2021, 01:21 AM
(03-26-2021, 08:42 PM)Vinny Wrote: Not sure where this fits most, here or electronics, but I have already used it in on something I'm machining so I guess this works. I had one of these at work that I used for years and finally got one here. I mounted it to a scrap piece of corian I had layin around and put some stick on rubber feet on the bottom. This was a $25 ebay find. I had one at work that I used a lot. Very handy for electronics work. Ed
03-28-2021, 12:06 PM
Not sure what attachments are available besides the circuit board holder, but I have a stand for those that's like a rotisserie that I really like for that.
On the machining front wrt latest deliveries ... Behold, the oil pump! I saw a video of someone in the Burke milling group who recently did this to his Burke except I don't have zerks on my Index. Excuse the bag still being around it, I went to take it out and it's got the usual Chinese oil (at least it's not the mysterious yellow goo) all over it so it's staying in the bag till I'm ready for it. I'll probably do it when I pull the mill out to replace the table feed belt. BTW, it was $20 on ebay.
Logan 200, Index 40H Mill, Boyer-Shultz 612 Surface Grinder, HF 4x6 Bandsaw, a shear with no name, ...
the nobucks boutique etsy shop | the nobucks boutique |
« Next Oldest | Next Newest »
|