Head Studs
#11
HI i don't no if this will help but its good practis to replace all the head studes and nuts as all can be cum week with age
krv3000, proud to be a member of MetalworkingFun Forum since Feb 2012.
Reply
Thanks given by:
#12
We have CAT engines at work with over 6,000 HP and cost over a million bucks. My brother in law works at Cat in the parts dept. My mom retired from there. I was too stupid to get a job there...Bob
Bob Wright
Metal Master Fab
Salem Ohio
Birthplace of the Silver and Deming drill bit.
5 Lathes, SBL Shaper, Lewis Mill, 7 drill presses, 5 welders...
Reply
Thanks given by:
#13
(03-27-2012, 06:39 PM)aametalmaster Wrote: We have CAT engines at work with over 6,000 HP and cost over a million bucks. My brother in law works at Cat in the parts dept. My mom retired from there. I was too stupid to get a job there...Bob

Doing a complete inframe, pistons liners rings bearings, surface head, all new valves etc will be reusing bolts as they are ok. Last inframe was done all cat reman parts, found out cyl packs they used were used piston domes, also KW where the job was done never cut the block for inserts and failed to made sure
cyl protrusion was set right. You can bet KW is not doing the work this time as well as you can bet there are no rebuilt used parts either. Finning here the Cat dealer charges $142.00 per hr for a mechanic that is slower than my mother would be, KW rate is $112.00 hr, I have a qualified Cat mechanic working for me for $75.00 hr which I can live with. The jobber parts at least in my opinion look better than the cat pieces at 1/2 the price. The jobber parts are warranted for the parts as well as the labor. Cat is out to lunch both on their parts and labor prices. tom
Logan 10x26" lathe
SIEG 12x40" lathe
RongFU 45 clone mill
6" import band saw
Baldor Grinder
thousand of tools+tooling pieces 40 yrs of collecting
Reply
Thanks given by:
#14
Just in case anyone is interested cost of complete inframe about 12,000 using quality parts from IPD, AFTER INFRAME still had an injector problem so a new set of CAT C18 marine application injectors engine now makes about 700+ HP, puts the fun back in driving for an old man hihi. tom
Logan 10x26" lathe
SIEG 12x40" lathe
RongFU 45 clone mill
6" import band saw
Baldor Grinder
thousand of tools+tooling pieces 40 yrs of collecting
Reply
Thanks given by:
#15
Tom,

What is this thing you're sinking that much money into? An earth mover of some sort?

Ed
Reply
Thanks given by:
#16
(04-03-2012, 06:40 PM)EdAK Wrote: Tom,

What is this thing you're sinking that much money into? An earth mover of some sort?

Ed


On the thread you mentioned the scooter you would like at the end I posted a couple of pics of my bike, one pic shows my truck in the background, that is my earthmover, I have 50,875 hrs logged in the drivers seat. I never idle when sleeping so all those hrs are driving. 50,875 hrs driving =2119.8 days or
5.8years behind the wheel driving 24 hours a day just shy of 4 million kilometers. ALL WITHOUT ANY ACCIDENTS at the present time I average 12.5 thousand miles per month or more a month than mostr people drive in a year. tom
Logan 10x26" lathe
SIEG 12x40" lathe
RongFU 45 clone mill
6" import band saw
Baldor Grinder
thousand of tools+tooling pieces 40 yrs of collecting
Reply
Thanks given by:
#17
Tom,

OK, I do remember seeing that Kenworth. You sure do put a lot of miles on that earth mover. Big Grin

Ed
Reply
Thanks given by:
#18
That is a good looking rig Tom. My dad was a OTR driver until the day he died. Only saw him every other day as he was always on the road. He also had a gazillion mile safety record.

Smiley-signs107
Willie
Reply
Thanks given by:




Users browsing this thread: