Log Splitter
(02-04-2015, 05:35 PM)DaveH Wrote: After reading Vt's post about getting his nuts or bolts bent I've redesigned my pusher block and put the bolts from the bottom.

I thought his concern was getting his nuts hit, not bent.
Hunting American dentists since 2015.
Reply
Thanks given by:
(02-04-2015, 05:35 PM)DaveH Wrote: After reading Vt's post about getting his nuts or bolts bent I've redesigned my pusher block and put the bolts from the bottom.



Smiley-eatdrink004
DaveH

No need Dave, I believe Vt's splitter has the moving wedge therefore split pieces could hang up on the bolts.
My splitters  (2) have NEVER had any bolt damage on the carriage or "pusher".
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Reply
Thanks given by: DaveH
Yes, the moving wedge gib screws were what got hung up because the carriage moves through the split. A pusher like Steve's (and yours) doesn't move through the wood, so wouldn't get hung up.

Sorry I didn't get a chance to completely uncover the splitter today, 4 inches of new snow, and the road crew trucks throwing more snow over the already high banks meant shoveling. I did get the tarp up for about half the splitter but the rest is frozen into block ice. I didn't want to tear it, but I;ll get it chipped off tomorrow, and get you some photos.

Mayhem was right! The gib screws can be replaced....... Rotfl
Reply
Thanks given by:
Sorry Vt causing you a lot of trouble.
Smiley-eatdrink004 
DaveH
Reply
Thanks given by:
Not at all Dave. I do. need to free it, and happy to help if I can.

I like your splitter design
Reply
Thanks given by:
(02-05-2015, 07:30 PM)vtsteam Wrote: I like your splitter design
Thanks Vt but a lot of the credit has to go to the guys on here .............. they have really helped a lot. Thumbsup .
Smiley-eatdrink004
DaveH
Reply
Thanks given by:
Hi Dave, here are some photos.

The wedge is a casting and 6" long by about 3-1/2" wide -- 45 degree included angle. It is cast integral with the chevron shaped carriage. The wedge is hollow.

The tail plate is 1-3/4" thick and about 8" x 14". It has a ring shaped dog to keep wood from popping (mostly does!).

The red guards near the cylinder attach point are the fingers that will pull the wedge out of a stuck log if you retract.

The pump is dual speed -- shifts to low if the pressure gets high enough.

Overall the whole rig seems slow for my rate of working, even though dual speed.

It can be rotated to vertical for really big sections, though I never have -- I wrestle some pretty big stuff up onto the bed -- too lazy to change over -- though I'm not sure that's actually being "effectively" lazy...... maybe just dumb!

The tank is part of the axle assembly a big rectangular section tube that runs across the splitter.

The "ways" are an I beam with another slightly narrower plate (probably cold rolled) lapped on top and intermittent welded.

The controls are on the side, with a side facing lever. I don't have any trouble reaching it and holding onto a log at the same time.

Any more info needed, just ask.... Smiley-eatdrink004


Attached Files Thumbnail(s)
                                           
Reply
Thanks given by:
Thanks Vt, appreciate the time and effort to post the pics Thumbsup 
The first thing that hit me was the size of the wedge Jawdrop  Wow!
I will have a few questions I'm sure just need some time to look Thumbsup 
Smiley-eatdrink004 
DaveH
Reply
Thanks given by:
Vt,
Really nice log splitter Thumbsup  the thing I like the most (besides the 25 ton, 'cause that is just envy Big Grin )  is the manner how the cylinder is fixed.
Does one need a special cylinder to fix it that way?
Smiley-eatdrink004 
DaveH
Reply
Thanks given by:
(02-06-2015, 12:04 PM)vtsteam Wrote: The "ways" are an I beam with another slightly narrower plate (probably cold rolled) lapped on top and intermittent welded.
Hi Vt, any idea why that was done?
Smiley-eatdrink004
DaveH
Reply
Thanks given by:




Users browsing this thread: 13 Guest(s)