5 Cylinder Radial
I have managed to put together another slide show video.

https://youtu.be/Yf4Olv524Kg  





It gives a bit more information on the build.

Brian.
Brian, proud to be a member of MetalworkingFun since Sep 2012.
http://briansworkshop.weebly.com Welcome
Reply
Thanks given by:
My apologies for not keeping up with this thread.
however the situation to date is that i cut the first accessory shaft gear and found that the cutter was marked No 5 was in fact a No 7
This rather changed things as i now must wait for the replacement. The vendor suddenly ran out of stock??
So i have continued with  the other sections at the rear of the case.
   

Further work has also been done on the belt sprockets using the faulty accessory shaft as a dummy.
The slackness of the belt is due to the absence of the cylinder head & cylinder base gaskets also the position of the belt pensioner has yet to be determined, but over all I am very happy with the result.

   

Brian  Smiley-dancenana
Brian, proud to be a member of MetalworkingFun since Sep 2012.
http://briansworkshop.weebly.com Welcome
Reply
Thanks given by:
That must have had you scratching your head. 17428

Tom
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by:
Hi Tom the 25 T gear came out with pointy teeth .

   

So I rummaged is the scrap box, found a piece of aluminium and cut a perfect
16t gear on it I was not a happy bunny.

   


Brian.   Smiley-dancenana
Brian, proud to be a member of MetalworkingFun since Sep 2012.
http://briansworkshop.weebly.com Welcome
Reply
Thanks given by:
Further work has now been done on the back plate, the seating's for the accessory shaft  bearings have been machined so the plate can now be fitted with the dummy shaft.
The flanges for the camshaft sprocket have been made, the outer one is thicker to accommodate  the small magnet for the ignition trigger. this flange can be rotated independently to adjust the ignition timing for that individual cylinder.
With a temporary head gasket of the correct thickness added the belt tension now looks a lot better.

     

   

Slowly  slowly     Brian.   Smiley-dancenana
Brian, proud to be a member of MetalworkingFun since Sep 2012.
http://briansworkshop.weebly.com Welcome
Reply
Thanks given by:
That is coming along very nicely, even with knowing the scale it looks MASSIVE .....
damn cool !

greg
Magazines have issues, everything else has problems

Reply
Thanks given by:
The latest work.
I made a simple engine stand  so it is now possible to assemble  the engine to keep most of the parts in one place.
 Further work has been done,  the top fins on the remaining heads and cam boxes are nearly done. and i have tapped some of the threads in the casing so the assembly holds together, Just the thought of braking a tap in the case gives me goose bumps.
So this is what it looks like now.

   

   

Brian. Smiley-dancenana
Brian, proud to be a member of MetalworkingFun since Sep 2012.
http://briansworkshop.weebly.com Welcome
Reply
Thanks given by:
OOOOOO ! I LIKE IT .

After you get the radial built, how about an engine stand.


greg


Attached Files Thumbnail(s)
   
Magazines have issues, everything else has problems

Reply
Thanks given by:
(10-28-2016, 09:27 PM)pepi Wrote: OOOOOO ! I LIKE IT .

After you get the radial built, how about an engine stand.
greg

I think he is going to use it to power his boat Big Grin
Hunting American dentists since 2015.
Reply
Thanks given by:
Just perhaps a semi scale spirit of St Louis .  Slab sided, easy to make from foam sheet, a good load carrier at slow speed .!!!! 
   
But it has to run yet, a long while to go.
No more dreams.

 Brian Smiley-dancenana
Brian, proud to be a member of MetalworkingFun since Sep 2012.
http://briansworkshop.weebly.com Welcome
Reply
Thanks given by:




Users browsing this thread: 3 Guest(s)