Installing QCTP to the Kobe lathe
#1
It has taken me a while but I have finally got the QCTP installed on my lathe. Probably a total of about 4 hours work but has taken me a fortnight to find those 4 hours.
I needed to put a shim under the toolpost to get the tools up to centre height. I wanted to keep the spigot lug on the topslide so that the original SCTP can be re-installed, so I found a suitably sized bit of round unknownium to make the shim. Discovered as soon as the tool touched it that it is in fact cast iron.
   

Having made the spacer disc to the estimated necessary thickness, it was necessary to mill the spigot to a matching height
   

I didn't have a 22mm tap to thread the spigot hole, so i decided to use the existing 5/8 UNC thread which required making a suitable stud with different sized ends. Had an odd hold-down bolt witht he same thread as the existing toolpost centre bolt so I cut the T-end off it, turned it to size and threaded it to the 5/8 UNC required to go in the topslide hole. I seem to have lost the photos I took of that job, but here is what i ended up with
   
Unfortunately the lever pointed the wrong way and I didn't have any appropriate size washers to put under it to make it point in a more suitable direction.

I found that I had miscalculated (misguesstimated) the required shim thickness and the toolpost was a bit too high, the holders were nearly bottoming out when at centre height. I decided to lower the setup by .300". In the process I decided to clean up that horribly worn surface on the topslide. Putting the topslide in the lathe would have been an easy way to do this, but only having one lathe meant I had to make my first-ever use of the rotary table in the mill. Took me ages to set it up with the spigot centered on the rotary table, partly because the thing is so low geared it takes ages to make a revolution to compare indicator readings.
   

The surface cleaned up nicely with a shoulder mill run up to the edge of the spigot.
   

I milled the top of the spigot down the .300" whilst it was in the mill, then put the topslide back on the lathe and refitted the old SCTP so that I could turn the spacer disc down to the required thickness.
Bunged it all together and adjusted the toolholders to centre height, now they are all close to the middle of their up/down travel. I abandoned the idea of using the old lever nut, think I'll make a nice domed hex nut to suit one of the old megaspanners I have lying around.
this is where I finished up tonight before my steak-cooking skills were required.

   


Thanks again Arvid Thumbsup

One minor issue remains; the piston pad on the boring side of the QCTP is a little proud of the toolpost and only a couple of the tool holdrs have a deep enough throat to actually go over it.
   
I think I need to take a couple of thou off the thickness of the piston pad. A surface grinder would be the best tool for this but I don't possess such an animal; will have to ponder this, can't see myself getting back in the workshop for several days anyway.
Lathe (n); a machine tool used in the production of milling machine components.

Milling Machine (n); a machine tool used in the production of lathe components.
Reply
Thanks given by:
#2
Nice work Pete.
Hunting American dentists since 2015.
Reply
Thanks given by:
#3
If you have a dovetail cutter, use that to slightly modify the toolholders. I've had to do that with a couple of the cheap chinese holders.
Logan 200, Index 40H Mill, Boyer-Shultz 612 Surface Grinder, HF 4x6 Bandsaw, a shear with no name, ...
the nobucks boutique etsy shop  |  the nobucks boutique
Reply
Thanks given by:
#4
(05-24-2016, 04:45 PM)Vinny Wrote: If you have a dovetail cutter, use that to slightly modify the toolholders.  I've had to do that with a couple of the cheap chinese holders.

You're suggesting to widen the dovetail in the holder? I'll have a good look and see if that looks like a goer- I guess that will make the holder sit a little further out from the toolpost. I'm concerned about making them too loose. Think I have a dovetail cutter in the pile somewhere so might give that a go.
Lathe (n); a machine tool used in the production of milling machine components.

Milling Machine (n); a machine tool used in the production of lathe components.
Reply
Thanks given by:
#5
By the way, I had been wondering why everyone was saying they replace the dog-point setscrews in the holders. I assume it's because there isn't an allen key known to man that actually fits the chicom screws?
Lathe (n); a machine tool used in the production of milling machine components.

Milling Machine (n); a machine tool used in the production of lathe components.
Reply
Thanks given by:
#6
(05-25-2016, 03:41 AM)Pete O Wrote: By the way, I had been wondering why everyone was saying they replace the dog-point setscrews in the holders. I assume it's because there isn't an allen key known to man that actually fits the chicom screws?

No, it's because they're made of cheese.

Ed
Reply
Thanks given by:
#7
You can more easily fix the tight holders by just taking a tiny bit off the bottom of the mating dovetail. No need to get in there with a dovetail cutter, it only needs clearance for the piston and the dovetails themselves likely have plenty of clearance already.

Some of those blocks are very hard. I would use a surface grinder if you have one.
Reply
Thanks given by:
#8
I got a bit of time this afternoon to have another run at this thing; I decided to take some of the thickness off the piston pad from the boring side of the toolpost, rather than remove material from the holders. A couple of reasons for this; firstly, pretty much all of the holders seemed to go over the dovetails okay and with almost the same dovetail fit (by feel) except for one of the non-original holders which is a bit tighter than all the others. Every one of the holders was difficult to get down over the piston on that side, so I think the fact that the piston was a bit proud was affecting every holder. Secondly, not having a surface grinder, I was not confident to take a cut out of the middle of the holder dovetails without stuffing them up.
I used a small surface plate with a sheet of 180 grit emery paper and about half an hour of rubbing interspersed with test fitting. All of the holders except the one with the tighter fit on the dovetail, now slide happily onto either position. I'm happy to leave that one holder as-is and put a turning tool in it.
   

   

   

I'm optimistic about getting some time this week to make some more of the milling arbor spacers, really looking forward to doing the job with the QCTP now, it was very laborious with the old arrangement. Once I have the spacers and nut for the horizontal mill finished, I'll look at making some more holders- first on the list will be a holder for the carbide insert parting tool. I'll be looking for some advice on material to use for the holders.
Lathe (n); a machine tool used in the production of milling machine components.

Milling Machine (n); a machine tool used in the production of lathe components.
Reply
Thanks given by:
#9
Nice work Pete.
Hunting American dentists since 2015.
Reply
Thanks given by:




Users browsing this thread: