How to start
#31
I bought a German set or ER-32, haven't been disappointed. All of the ER-32 collet chucks I have are chinese tho. I have 1 div or less movement on a 0.0005" DTI on all of them.
Logan 200, Index 40H Mill, Boyer-Shultz 612 Surface Grinder, HF 4x6 Bandsaw, a shear with no name, ...
the nobucks boutique etsy shop  |  the nobucks boutique
Reply
Thanks given by:
#32
I've bought 3 sets of ER 32 collets from BangGood, Two fractional and one metric, so far they are great, the ones I've checked, had very minimal run out, less than I can measure.

I bought my R8 x ER 32 collet chuck from LMS, on sale for about $60, its fabulous. I did drill a 3/16" hole in the side, so I could hold the collet chuck, with a pin wrench and tighten the nut with the supplied wrench, putting the wrenches next to each other, easier for me to tighten/loosen.
jack
Reply
Thanks given by:
#33
It started...

   

Open on suggestions for tutorial books or videos for complete beginners.

Thanks,

D.
Reply
Thanks given by:
#34
Lots of videos on YouTube. Tom's Techniques are some of the best.

For a book, download the pdf of the US Navy's Machinery Repairman 3 and 2
Reply
Thanks given by:
#35
(03-23-2018, 09:18 AM)Dr Stan Wrote: Lots of videos on YouTube. Tom's Techniques are some of the best.

....

Yup, that's certainly one of the better sources of tutorial videos.

Tom's Techniques

Ed
Reply
Thanks given by:
#36
Presently in the process to put together an essential tool kit to start practicing.

I still could not make up my mind on surface milling and finishing. I understand that the options are:
1) Fly cutters
2) Face mills

Fly cutters look cheaper, but I understand you also need a grinder to take care of the blades.
An indexed face mill, looks more expensive, but I have the feeling it might create less problem for a beginner. From what I read, if I had to pick one, I should go for a 45 degrees. Not sure if the arbours for these are standard, or each brand has his own.

What's your take in the matter ?

Thanks,

Davide
Reply
Thanks given by:
#37
As a beginner, I would recommend avoiding carbide. It is expensive, unforgiving and generally intended for larger, more powerful machinery. A fly cutter and a few high speed steel bits would be the way to go. Hand sharpening is a skill you will want to learn anyway and there are plenty of videos on my Youtube page and information on my website to steer you in the right direction.

A few basic things you will need for the mill are:
  •  A dial test indicator to align the vise to the table
  • An edge finder to locate the edges of parts
  • A small solid square for squaring up stock
  • An assortment of small end mills, four-flute for steel and two-flute for non-ferrous metals, plus collets to hold them
  • A set of thin parallels
  • Digital calipers
  • A drill chuck and a set of twist drills
  • A calculator to figure proper rpm for the end mills, to keep from killing them
You should be able to do a lot of damage with this list and add to it as you gain experience and your bank account allows. Big Grin

Tom
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by:
#38
Thanks,

I have almost everything. Only thing missing are the edge and center finder and the parallel. Both are on the shopping list.
I also came to the conclusion the HSS would be more forgiving.

Can I ask why you would not recommend to have a something like in the picture for the finishing ? I think the blades can still be in HSS.

Otherwise I have to add to the list the fly cutter holder, the biased and a grinder.

Additionally, I will probably be in US in the near future. Do you know any good place to shop tools around Oak Ridge, or recommended web shop to order from ?

Thanks,

Davide


Attached Files Thumbnail(s)
   
Reply
Thanks given by:
#39
Davide,

A multi insert face mill will likely chatter on a light bench mill like yours. They are better suited for larger, more rigid mills.

Check the links page on my website (Tomstechniques.com) for suppliers. A few that come to mind are Little Machine Shop, Shars and Travers.

Tom
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by:
#40
(04-05-2018, 04:32 AM)Nikon1975 Wrote: Presently in the process to put together an essential tool kit to start practicing.

I still could not make up my mind on surface milling and finishing. I understand that the options are:
1) Fly cutters
2) Face mills

Fly cutters look cheaper, but I understand you also need a grinder to take care of the blades.
An indexed face mill, looks more expensive, but I have the feeling it might create less problem for a beginner. From what I read, if I had to pick one, I should go for a 45 degrees. Not sure if the arbours for these are standard, or each brand has his own.

What's your take in the matter ?

Thanks,

Davide

My take is to watch Tom's videos. Most of your questions would be answered.

Ed
Reply
Thanks given by:




Users browsing this thread: