Todays Project - What did you do today?
But without cell coverage I can't keep an eye on you guys.
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:
Bit of yard cleanup then went logging. Well went out in the bush behind my place and retrieved some logs the loggers couldn't sell, no market for hemlock these days.
[Image: IMG_0731.jpg]

Makes nice timber for framing, heavy but thats why we got machines.
Cut these 6 x 6 and 3 x 6 last week end, if you don't recognize it, its a blacksmith shop / foundry in kit form. Some assembly required.

[Image: IMG_0732.jpg]
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:
That's some very nice lumber you got out of those logs.

Ed
Reply
Thanks given by:
That was stuff I sawed last week, these logs are to finish the kit.
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by: EdK
What do you mean "No market for Hemlock?"Idea
We've pretty much all got wives,
I'd have thought "Hemlock" would be quite valuable Jawdrop

"No dear, just chatting online with my Metalworking friends"
"They've given me a new idea of how to get some new machine tools"
"Would you like a nice cup of tea"
"Well mine tastes OK"
"Nite Nite honey"
"Now where is that machine tool catalogue"

RotflRotflRotflRotflRotflRotflRotflRotfl

Rick

PS, Shhhhh!!!!!
Whatever it is, do it today, Tomorrow may not be an option and regret outlasts fatigue.
Reply
Thanks given by:
And people think I'm a bad man!
Hunting American dentists since 2015.
Reply
Thanks given by:
Rotfl
Smiley-eatdrink004
DaveH
Reply
Thanks given by:
Well you all were thinking it Big Grin
Whatever it is, do it today, Tomorrow may not be an option and regret outlasts fatigue.
Reply
Thanks given by:
Well... today I finished... sort of... a job I started with my late father 9 years ago.

In his words it was the last press he would ever need, the one that would "see him out" I suppose it has, and it is all mine now, I can't imagine ever needing another one for my personal use, so it'll see me out too.

For the interim I have fitted a relatively small bottle jack, when I get around to it I'll fit the "Big" ram.

Photo time,
   
At this point most of you will be saying "what's so special about this press" Well,,, that little weeny bottle jack is actually a 20 ton air powered one, and that blue lump hanging off of the left hand side is a counterweight for the "Beam" or "Table" It was the only thing I had in the shop that was heavy enough in one piece, It was a Ford 351 CI Cleveland engine block that had been left to "season" for a little too long in a damp place, the bores were too badly rusted to use so I use it as a mock-up or used to, now I use it as a counterweight.

   
See 20 tons, and it's quite big when you need to lift it in to place but looks very small when it is in place, it has a 1 5/8" piston which is tiny compared to the 6" piston in the big ram which the press was designed for, with the big ram I should have 125 tons on tap, this was designed to be the last press we will ever need and I've never needed more than 125tons.

   
My favorite piece, the Hot water tap/faucet handle used as a cylinder return valve handle, there's a story to that piece, Dad always used a chromed tap handle as a cylinder return valve on his porta powers, jacks and presses, so it had to be, he used to say the "H" stood for Hydraulic.

As far as dimensions go the press will take 3 feet and clearance between the posts and the beam is made from two 1" x 8" x 44" high alloy steel plates as is the top frame, designed to take every bit of force that the six inch ram can deliver.

So like I said today I finished something, the first "Joint project" finished since Dad passed.

Best Regards
Rick
Whatever it is, do it today, Tomorrow may not be an option and regret outlasts fatigue.
Reply
Thanks given by:
Nice, but wouldn't it have made more sense to have the jack mounted upside down? The smaller diameter of the piston would allow you to fit it into tighter spots and/or easily fit ram attachments to press bushings, bearings and other things.
Reply
Thanks given by:




Users browsing this thread: 24 Guest(s)