Todays Project - What did you do today?
Smiley-signs009
Smiley-eatdrink004
DaveH
Reply
Thanks given by:
(10-23-2013, 08:47 AM)Mayhem Wrote: Wow - that is quite the difference. I'd love to see some video of these machines in action.

Your wish is my command:

http://www.youtube.com/watch?v=a7O5q1RR9zA

http://www.youtube.com/watch?v=kNKYl7KkCds
Andrew Mawson, proud to be a member of MetalworkingFun Forum since Oct 2013.
Reply
Thanks given by: Mayhem
Very nice Thumbsup
Still fascinates me to watch them. I wish I could thread that quick Big Grin
Smiley-eatdrink004
DaveH
Reply
Thanks given by:
Well during its 'soak test' that Traub TNC350G re-cut that poor old 20mm thread over a hundred times this morning, and amazingly the thread is still superb :) Try doing that manually !
Andrew Mawson, proud to be a member of MetalworkingFun Forum since Oct 2013.
Reply
Thanks given by:
(10-23-2013, 09:56 AM)awemawson Wrote: Well during its 'soak test' that Traub TNC350G re-cut that poor old 20mm thread over a hundred times this morning, and amazingly the thread is still superb :) Try doing that manually !

So what exactly are you going to do with these 100 20mm threads ?
tekfab, proud to be a member of MetalworkingFun Forum since Apr 2013.
Reply
Thanks given by:
hehe . . . well it was re-cutting the same thread each time - I'm too tight to use all that steel up :)
Andrew Mawson, proud to be a member of MetalworkingFun Forum since Oct 2013.
Reply
Thanks given by:
Finished number 2 of 2.

Ed

   
Reply
Thanks given by:
Nice Ed - so what are they for?

Also, they must be really small or you have really big sheets of toilet paper over there!
Hunting American dentists since 2015.
Reply
Thanks given by:
(10-24-2013, 07:11 PM)Mayhem Wrote: Nice Ed - so what are they for?

Also, they must be really small or you have really big sheets of toilet paper over there!

Rotfl That's a paper towel they're sitting on.

They're about 2.25" long and 1/4" in diameter. Made from some 303 SS shafting I got from work that they were going to throw out. They're parts to enhance my aluminum step blocks that I made from Tom's design. I'll post a picture once the project is done. It's a simple project, once I figured out the problem with threading on the lathe, that is nice to do if I'm not in the mood to work on something that requires more than a small amount of brain power. Smile

Ed
Reply
Thanks given by:
I've been working on a machine at work to weld a thin mylar sheet to an injection molded part. It's part of a product manufacturing system that I am responsible for and this is one of the fixtures designed and built by yours truly. The concept is an injection molded PET part is inserted into the fixture and a mylar membrane registered on top of it. Then the two parts are presses against a mask with a pneumatic mechanism and scanned under a 300 watt solid state laser which fuses certain parts of the membrane to the part. I originally tried to use an adhesive to attach the two pieces, but there were numerous problems associated with it so I ended up doing this welding thing which works great. This week, I stripped the prototype unit down, had all of the machined parts (50+) black anodized and finish dressed all of the wiring. I learned enough developing the servo drive for this thing that I'm pretty confident I could roll my own CNC mill. Just another project to add to the list.

Oh and of course it didn't work when I reassembled it all after anodizing. When I disconnected the cables a jumper fell out of a terminal block on to the floor and I didn't notice until after half a day of troubleshooting, trying to find the cause of all the screwy floating voltages. Angry

The product is slated for release at years end so I'll be able to expand a bit on what it does at that time.

I apologize for the crappy pics, but iPhone's seriously suck as cameras in low light.

Tom

[Image: IMG_0209.JPG]

[Image: IMG_0208.JPG]

[Image: IMG_0205.JPG]

[Image: IMG_0207.JPG]
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by:




Users browsing this thread: 107 Guest(s)