Todays Project - What did you do today?
What is that assembly Ed? Looks good, I just can't figure out what it is.
Reply
Thanks given by: EdK
(10-30-2013, 06:19 PM)PixMan Wrote: What is that assembly Ed? Looks good, I just can't figure out what it is.

Thanks Ken.

It's these: http://www.metalworkingfun.com/showthread.php?tid=846

I dislike needing a tool to use a tool so I replaced the SHCS with a custom thumb screw.

Ed
Reply
Thanks given by:
(10-30-2013, 05:49 PM)f350ca Wrote: Spent the afternoon moving firewood into the shed, only 1/4 full, disheartening.
I know EXACTLY what you mean Greg! Sweat
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Reply
Thanks given by:
(10-30-2013, 08:02 PM)stevec Wrote:
(10-30-2013, 05:49 PM)f350ca Wrote: Spent the afternoon moving firewood into the shed, only 1/4 full, disheartening.
I know EXACTLY what you mean Greg! Sweat

If we could only harness the heat we generate cutting and handling firewood we'd heat for half the season.
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:
Looks good Ed, but WAY to shiny. They get the crap beat out of them on the mill. BTW, that cap screw is staked in position. No tools required.

Tom
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by: EdK
Not exactly today but recently with Charlie's aid I converted a bunch of my uncles old 8mm movies to digital. Preserved some history and a lot of memories. Captured the projected image with his Canon 5D mark II
Here is a short clip of the last steam train through Calabogie. Scary part is I remember as a kid going down to see it go past every day.

http://youtu.be/nijFnMHynDQ
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:
(10-30-2013, 05:57 PM)dallen Wrote: started working on making a couple drip oilers for my shaper...

Any chance of a full thread on this project Dave? I would like to make some for my lathe.
Hunting American dentists since 2015.
Reply
Thanks given by:
(10-30-2013, 08:24 PM)TomG Wrote: Looks good Ed, but WAY to shiny. They get the crap beat out of them on the mill. BTW, that cap screw is staked in position. No tools required.

Tom

Tom,

I do use them quite a bit. I just try to keep them clean. I like to tighten the screw up so the unused leafs don't flop around during use and also for storage.

Ed
Reply
Thanks given by:
Great old video Greg, looks like it was spring run-off time.
sasquatch, proud to be a member of MetalworkingFun since Jul 2012.
Reply
Thanks given by:
Needed to true up a 4 foot chunk of 2 inch sched 40 black pipe. Horible stuff to get a finish on and not deflect in the middle, I hate follow rests.
Someone showed a shear tool on one of the other forums, never heard of one before.
Ground one up from 5/8 HSS and gave it a shot.
Roughed the pipe round at 5 or so thou DOC and .0175 in/rev feed at 200rpm. Unbelievable finish with little to no chatter.
Made a vanity pass at 2 or so DOC and .008 in/rev and 200 rpm.
No taper overall, about 1/2 thou over in the middle.
Im sold on this cutter, guess you can't hog metal with it but you can't hog on black pipe anyway.

[Image: IMG_0841.jpg]

Held in the three jaw and three jaw tailstock chuck.

[Image: IMG_0843.jpg]
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:




Users browsing this thread: 25 Guest(s)