Todays Project - What did you do today?
(03-23-2014, 07:55 PM)PixMan Wrote: I took the nut out of the chuck thinking it would run down the whole thread, not so. I had to put it back in and take another thousandth or two. That's a pain in the butt!

I hesitate to say this Ken but, nyah, nyah, I told you so. Rotfl

Glad you were able to correct it. Thumbsup
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Reply
Thanks given by:
Still not sure why it did that because there really doesn't seem to be ANY taper in the screw.

If you've ever made mating Acme screws you would know just how oddly they fit together. The tiniest change in pitch diameter or thread form can be the difference between binding up, smooth fit or just plain wonky fit. The nut now sails from end to end on the screw and there's no measureable difference in clearance anywhere.
Reply
Thanks given by:
Nice job on the nut Ken (and the tool). It looks like you got a good grade of bronze for machining.

Another easy way to reacquire a thread is to run the tool into the bore with it retracted and stop the spindle with the lead screw engaged. Then you can sort of feel your way into the thread using the compound and cross slide to get close and finish up under power (cross slide till it touches and compound to depth). It's definitely easier on coarse threads than fine ones.

What more needs to be done on the screw?

Tom
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by: PixMan
Exactly what I did Tom.

What's left to do with the screw is to turn the 20mm diameter and M12x1.75 thread, them mill keyways and drill a hole through it. Look for Darren's print in the Milling Machine section under Kondia rebuild thread.
Reply
Thanks given by:
The hole through the key slot confuses me. I cannot see a function for it other than to knock the key out should it get stuck. There are other shafts with key slots on this mill that don't have a through hole, so it is not a consistent feature.
Hunting American dentists since 2015.
Reply
Thanks given by:
Darren is it possible that under a previous ownership, whatever it is that is now held by the keyway was once pinned to the shaft?
Is it a straight key or a woodruff? Maybe the hole was to pin the straight key? Chin
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Reply
Thanks given by:
Attached the prints he sent me. You can see the 3.5mm hole going through the shaft for no readily apparent reason other than to perhaps make it weaker. Chin

If anything could use that hole as a knockout, it should be that blind 5mm pin hole!


Attached Files
.pdf   Kondia FV-1 Elevating Screw and Nut_rev1.pdf (Size: 416.08 KB / Downloads: 18)
Reply
Thanks given by:
Steve - I'm currently in Europe at a meeting, so I cannot refer to the original Kondia drawings. However, I don't believe that the shaft has been modified.
Hunting American dentists since 2015.
Reply
Thanks given by: stevec
only have three more of these to make, X Axis bearings for a router I'm working on.

open to suggestions on how to do snap ring grooves I need one in each end of the bore to hold the bearing in place.

[Image: X-Axis-bearing-bloxk0001.jpg]
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.

If life seems normal, your not going fast enough! Tongue
Reply
Thanks given by:
I've been wanting to make a two-in-one wrench for my QCTP for some time. I managed to slip it into the lineup after work today.

The main nut on the tool post is different than the one for the four-way tool post, so using sockets makes the most sense. I started with a pair of drive adapters for 3/8" and 1/2" drive. I turned a short piece of steel with bosses on the ends to fit the inside parts of the adapters.
   

I welded the adapters to the centre piece and drilled and tapped it for a threaded handle I had kicking around.
   

From this ...
   

To this.
   
Mike

If you can't get one, make one.

Hawkeye, proud to be a member of MetalworkingFun Forum since Jan 2013.
Reply
Thanks given by:




Users browsing this thread: 19 Guest(s)