|
milling in the lathe
|
03-20-2012, 04:56 PM
Thanks guys. Here are a few more. The vee groove is for my home made taper attachment where the block bolts to the ways and i have some pics of the TA too...Bob
Bob Wright
Metal Master Fab Salem Ohio Birthplace of the Silver and Deming drill bit. 5 Lathes, SBL Shaper, Lewis Mill, 7 drill presses, 5 welders... |
|
« Next Oldest | Next Newest »
|
| Messages In This Thread |
|
milling in the lathe - by krv3000 - 03-04-2012, 10:18 AM
RE: milling in the lathe - by DaveH - 03-04-2012, 10:22 AM
RE: milling in the lathe - by krv3000 - 03-13-2012, 05:23 PM
RE: milling in the lathe - by DaveH - 03-14-2012, 12:35 PM
RE: milling in the lathe - by ETC57 - 03-14-2012, 04:49 PM
RE: milling in the lathe - by doubleboost - 03-14-2012, 05:02 PM
RE: milling in the lathe - by ETC57 - 03-14-2012, 10:34 PM
RE: milling in the lathe - by DaveH - 03-14-2012, 05:26 PM
RE: milling in the lathe - by krv3000 - 03-14-2012, 05:42 PM
RE: milling in the lathe - by ETC57 - 03-14-2012, 10:44 PM
RE: milling in the lathe - by krv3000 - 03-15-2012, 02:07 PM
RE: milling in the lathe - by aametalmaster - 03-19-2012, 08:17 PM
RE: milling in the lathe - by aametalmaster - 03-19-2012, 08:18 PM
RE: milling in the lathe - by krv3000 - 03-20-2012, 02:41 AM
RE: milling in the lathe - by EdK - 03-20-2012, 06:29 AM
RE: milling in the lathe - by DaveH - 03-20-2012, 06:34 AM
RE: milling in the lathe - by ETC57 - 03-20-2012, 02:52 PM
RE: milling in the lathe - by aametalmaster - 03-20-2012, 04:56 PM
RE: milling in the lathe - by doubleboost - 03-20-2012, 05:04 PM
RE: milling in the lathe - by SnailPowered - 08-23-2012, 12:48 AM
RE: milling in the lathe - by EdK - 08-23-2012, 05:21 AM
RE: milling in the lathe - by SnailPowered - 08-23-2012, 03:36 PM
RE: milling in the lathe - by EdK - 08-23-2012, 03:40 PM
RE: milling in the lathe - by f350ca - 08-23-2012, 08:31 AM
RE: milling in the lathe - by DaveH - 08-23-2012, 08:38 AM
RE: milling in the lathe - by SnailPowered - 08-23-2012, 01:36 PM
RE: milling in the lathe - by DaveH - 08-23-2012, 02:22 PM
RE: milling in the lathe - by SnailPowered - 08-23-2012, 03:33 PM
RE: milling in the lathe - by aametalmaster - 08-23-2012, 06:31 PM
RE: milling in the lathe - by stevec - 08-23-2012, 06:45 PM
RE: milling in the lathe - by SnailPowered - 08-23-2012, 11:16 PM
RE: milling in the lathe - by Rickabilly - 09-17-2012, 07:10 AM
|
