04-07-2012, 09:38 PM
Well latest project is to find the workbench, or at least organize the tools hanging on the back wall that are used regularly.
Now my back wall is made from Slat-Wall. Peg board may have been better as the holes are spaced out better with adjustability every 1" but the slat wall was priced right "Free" Also dirt does not get behind slat wall as it can with the peg board holes.
Now either peg board or slat wall hooks are not really meant to have pieces taken off and put on regularly as the hooks fall out easily unless they are strapped in with the special little clips. Peg board hooks are even worse when used with slat wall.
So, to organize all my wrenches, imperial and metric I started by laying out the wrenches in a row on hooks to get the proper spacing.
For the hanger, I used 1/4 x 1 FB, 6 feet long (ie the length of the bench) I laid out the spacing as per what was determined by the first step, rounding up to even numbers so spaced out about 1" longer in the end.
I then set the mill up so that a 13/64 drill bit was centred over the 1" wide FB and proceeded to drill each increment. Then went back and taped each hole 1/4-20 NC. I also drilled holes about ever 2 feet for mounting screws.
Next step was to cut 1/4" diameter round bar to 3-1/4" long pieces. Face and lightly file a round on each end, then thread each piece on one end 1/4-20 NC by 5/16" long.
These pieces were threaded into the flat bar and tightened as best as could be done by hand, then the bar was turned over and the backs peened to prevent unthreading. I am sure locktite would have worked fine, but peening worked. Another option would have been press fit for the pin holes and spot weld each pin from the back.
Now I installed the rack but found that hammering on the bench caused the wrenches to fall off, so took the rack down and clamped as many fingers in the vise as I could, using a spacer block of about 1/2" thick to make sure all the pins stuck up equal amounts, then with 12" Crescent Wrench proceeded to bend each pin about 20 degrees. Used a straight edge to make sure they were all bent and aligned about the same. NB Make sure they are bent facing up!
Sorry but my daughter had borrowed my camera while I was making them so only pictures of finished project.
Also some pins were made by cutting down 1/4" bolts when I ran out of 1/4" RB.
It is fairly often that you need to grab two of the same size wrench, especially 1/2, 9/16 and 10 mm, so having more than one hanging is needed. Also there are Gear-Wrenches in short and long, regular combination wrenches and long combination wrenches, so depending on what is needed they are there for easy pickin'.
Left box end and open end in drawer of tool box as the combo's are more of the go-to.
The spacing I worked out is:
6 holes at 2" apart, next 4 at 1-1/2", next 7 at 1-1/4", 1 at 1-1/2", 2 at 2", 10 at 1-1/4", 5 at 1-1/2", 2 at 1-3/4" and final hole at 2"
I could have tightened this up by about a 1/16th per hole, but this made layout a bit easier. Also you want a bit a space between tools so they are not bouncing together.
This Layout gives from 1-1/4" to 1/4" imperial combos and 7 mm to 24mm metric combos along with the 10, 8 and 12" Crescent Wrenches.
Next project find room and organize the screw drivers.
Ok so got the screwdriver rack figured out and the workbench almost cleaned up.
Stock was 2 x 2 x 0.100 Tubing that has holes drilled every inch. It was a bit short for the bench so used a 1-3/4 x 1-3/4 tube inside as a stiffener then welded together. I wanted 5 feet long as the bench is six feet long, but needed clearance to swing the goose neck lights. I redrilled the holes in the splice area. Bent up two brackets to hang the tube from the slat-wall then welded them on in convenient locations.
Some of the holes were fitted with reducing bushings to prevent small items from just dropping through.
Walter
Now my back wall is made from Slat-Wall. Peg board may have been better as the holes are spaced out better with adjustability every 1" but the slat wall was priced right "Free" Also dirt does not get behind slat wall as it can with the peg board holes.
Now either peg board or slat wall hooks are not really meant to have pieces taken off and put on regularly as the hooks fall out easily unless they are strapped in with the special little clips. Peg board hooks are even worse when used with slat wall.
So, to organize all my wrenches, imperial and metric I started by laying out the wrenches in a row on hooks to get the proper spacing.
For the hanger, I used 1/4 x 1 FB, 6 feet long (ie the length of the bench) I laid out the spacing as per what was determined by the first step, rounding up to even numbers so spaced out about 1" longer in the end.
I then set the mill up so that a 13/64 drill bit was centred over the 1" wide FB and proceeded to drill each increment. Then went back and taped each hole 1/4-20 NC. I also drilled holes about ever 2 feet for mounting screws.
Next step was to cut 1/4" diameter round bar to 3-1/4" long pieces. Face and lightly file a round on each end, then thread each piece on one end 1/4-20 NC by 5/16" long.
These pieces were threaded into the flat bar and tightened as best as could be done by hand, then the bar was turned over and the backs peened to prevent unthreading. I am sure locktite would have worked fine, but peening worked. Another option would have been press fit for the pin holes and spot weld each pin from the back.
Now I installed the rack but found that hammering on the bench caused the wrenches to fall off, so took the rack down and clamped as many fingers in the vise as I could, using a spacer block of about 1/2" thick to make sure all the pins stuck up equal amounts, then with 12" Crescent Wrench proceeded to bend each pin about 20 degrees. Used a straight edge to make sure they were all bent and aligned about the same. NB Make sure they are bent facing up!
Sorry but my daughter had borrowed my camera while I was making them so only pictures of finished project.
Also some pins were made by cutting down 1/4" bolts when I ran out of 1/4" RB.
It is fairly often that you need to grab two of the same size wrench, especially 1/2, 9/16 and 10 mm, so having more than one hanging is needed. Also there are Gear-Wrenches in short and long, regular combination wrenches and long combination wrenches, so depending on what is needed they are there for easy pickin'.
Left box end and open end in drawer of tool box as the combo's are more of the go-to.
The spacing I worked out is:
6 holes at 2" apart, next 4 at 1-1/2", next 7 at 1-1/4", 1 at 1-1/2", 2 at 2", 10 at 1-1/4", 5 at 1-1/2", 2 at 1-3/4" and final hole at 2"
I could have tightened this up by about a 1/16th per hole, but this made layout a bit easier. Also you want a bit a space between tools so they are not bouncing together.
This Layout gives from 1-1/4" to 1/4" imperial combos and 7 mm to 24mm metric combos along with the 10, 8 and 12" Crescent Wrenches.
Next project find room and organize the screw drivers.
Ok so got the screwdriver rack figured out and the workbench almost cleaned up.
Stock was 2 x 2 x 0.100 Tubing that has holes drilled every inch. It was a bit short for the bench so used a 1-3/4 x 1-3/4 tube inside as a stiffener then welded together. I wanted 5 feet long as the bench is six feet long, but needed clearance to swing the goose neck lights. I redrilled the holes in the splice area. Bent up two brackets to hang the tube from the slat-wall then welded them on in convenient locations.
Some of the holes were fitted with reducing bushings to prevent small items from just dropping through.
Walter
starlight_tools, proud to be a member of Metalworking Forum since Apr 2012.