New Lathe
#18
Lathe arrived safe & sound Drool Drool Drool
Thanks to Stive at Landy Lift for a great job delivering it :bow: :bow:
Thanks also to Mick
The clean up is now well under way

[Image: S1340028_zpszhjx3pw9.jpg]

[Image: S1340027_zpsfqj1vxjx.jpg]

[Image: S1340023_zpss2rgggy8.jpg]

[Image: S1340026_zpsrpjcp4p3.jpg]

[Image: S1340021_zps4qsqkfjd.jpg]
[Image: S1340022_zps7rn02ued.jpg]

[Image: S1340025_zpswah5xcdo.jpg]
[Image: S1340024_zpsmonxydh0.jpg]

John
Reply
Thanks given by:


Messages In This Thread
New Lathe - by doubleboost - 02-22-2015, 12:27 PM
RE: New Lathe - by tekfab - 02-22-2015, 12:57 PM
RE: New Lathe - by EdK - 02-22-2015, 01:00 PM
RE: New Lathe - by mfletch - 02-22-2015, 01:23 PM
RE: New Lathe - by DaveH - 02-22-2015, 02:06 PM
RE: New Lathe - by Micktoon - 02-22-2015, 04:42 PM
RE: New Lathe - by doubleboost - 02-22-2015, 04:53 PM
RE: New Lathe - by mike-sid - 02-22-2015, 08:36 PM
RE: New Lathe - by krv3000 - 02-22-2015, 05:09 PM
RE: New Lathe - by Mayhem - 02-22-2015, 05:33 PM
RE: New Lathe - by Shawn - 02-22-2015, 11:09 PM
RE: New Lathe - by mike-sid - 02-22-2015, 11:19 PM
RE: New Lathe - by doubleboost - 02-23-2015, 06:29 PM
RE: New Lathe - by doubleboost - 02-23-2015, 06:29 PM
RE: New Lathe - by EdK - 02-23-2015, 06:39 PM
RE: New Lathe - by DaveH - 02-23-2015, 06:42 PM
RE: New Lathe - by Dr Stan - 02-23-2015, 06:53 PM
RE: New Lathe - by doubleboost - 02-28-2015, 02:54 PM
RE: New Lathe - by EdK - 02-28-2015, 02:58 PM
RE: New Lathe - by DaveH - 02-28-2015, 03:03 PM
RE: New Lathe - by Micktoon - 02-28-2015, 06:45 PM
RE: New Lathe - by f350ca - 02-28-2015, 08:44 PM
RE: New Lathe - by mike-sid - 02-28-2015, 09:03 PM
RE: New Lathe - by Highpower - 02-28-2015, 10:00 PM
RE: New Lathe - by trevatxtal - 03-01-2015, 03:29 AM
RE: New Lathe - by tekfab - 03-01-2015, 05:07 AM
RE: New Lathe - by Shawn - 03-01-2015, 06:07 AM
RE: New Lathe - by PixMan - 03-01-2015, 08:19 AM
RE: New Lathe - by mike-sid - 03-01-2015, 11:45 PM
RE: New Lathe - by doubleboost - 04-04-2015, 02:32 PM
RE: New Lathe - by DaveH - 04-04-2015, 03:44 PM
RE: New Lathe - by mike-sid - 04-04-2015, 05:34 PM
RE: New Lathe - by f350ca - 04-04-2015, 07:17 PM
RE: New Lathe - by Mayhem - 04-04-2015, 07:19 PM
RE: New Lathe - by EdK - 04-04-2015, 08:56 PM
RE: New Lathe - by Mayhem - 04-05-2015, 12:09 AM
RE: New Lathe - by PixMan - 04-05-2015, 09:37 PM
RE: New Lathe - by DaveH - 04-06-2015, 10:47 AM
RE: New Lathe - by krv3000 - 04-05-2015, 05:44 PM



Users browsing this thread: 2 Guest(s)