New toy PM-25MV update report
#9
Ok hers an update   and 3 pics sorry no mill  yet Ohhh  BC the camera died  and I don't think its the battery either . Now im in deeper water/ dog house ....    I dunno why  everything in my life goes the HRAD way .. yup and even  I have to compress pics too  its like a 3 fold operation  this is like consuming like another Hobby.........  . well  im taken a ride n for  berersand gona eat  so ill catch up latter

Quick update regarding draw bar   . I see one or two new felllas recently purchase the mill so I fig id share  what I have observed with current draw bar design . My Mill came with a Draw bar nut that was hammered from the go.    Because I haven’t tooled up anything as of yet  .I wasn’t sure with out using  the nut if it needed to hold draw bar concentric And it does ,  However the bushing idea works well.

I spoken with Matty last night he said he made a bushing and ya didn’t need  the  nut  sooooo

FWIW  the  this is what I did am doing > I am goin to make a new draw bar similar to Bridgeport  with a brass bushin. R For now I  will modify this one  and a later  put hex head nut to grab rotate and tighten,   I thought if it works on Bridgeport R8 style  than it should work same here .  Anyways  I didnt have any brass bronze at work   Had to come home with sumthin right ? So  I  actuality took  old brass air  fitting  and made my bushing on break time.  With my Morning  coffee I measured and drew a napkin sketch  if anyone is interested.   Well it worked I made bushing size on  . Next is to get either  put ½ or 5/8  extended Nut on end of draw bar machine down  to fit and weld on end.


…..When  I get my lathe I will make a new draw bar altogether that fits machine and handles well . Esp since you need to make tool changes quite often.


Attached Files
.jpg   DSCF0713.JPG (Size: 74.13 KB / Downloads: 84)
.jpg   DSCF0715.JPG (Size: 74.48 KB / Downloads: 85)
.jpg   DSCF0714.JPG (Size: 90.24 KB / Downloads: 84)
Reply
Thanks given by:


Messages In This Thread
New toy PM-25MV update report - by Kennyv - 06-12-2015, 09:23 AM
RE: New toy PM-25MV update report - by JScott - 06-12-2015, 09:55 AM
RE: New toy PM-25MV update report - by Vinny - 06-12-2015, 04:59 PM
RE: New toy PM-25MV update report - by EdK - 06-12-2015, 06:38 PM
RE: New toy PM-25MV update report - by Kennyv - 06-12-2015, 07:58 PM
RE: New toy PM-25MV update report - by EdK - 06-12-2015, 08:02 PM
RE: New toy PM-25MV update report - by Kennyv - 06-12-2015, 08:15 PM
RE: New toy PM-25MV update report - by EdK - 06-12-2015, 08:25 PM
RE: New toy PM-25MV update report - by Kennyv - 06-12-2015, 08:42 PM
RE: New toy PM-25MV update report - by Kennyv - 06-12-2015, 10:17 PM
RE: New toy PM-25MV update report - by Kennyv - 06-15-2015, 11:35 PM
RE: New toy PM-25MV update report - by Kennyv - 06-26-2015, 08:10 AM
RE: New toy PM-25MV update report - by DaveH - 06-26-2015, 11:49 AM
RE: New toy PM-25MV update report - by Kennyv - 06-26-2015, 11:09 PM
RE: New toy PM-25MV update report - by Kennyv - 06-26-2015, 11:13 PM
RE: New toy PM-25MV update report - by Kennyv - 07-10-2015, 05:12 AM



Users browsing this thread: 2 Guest(s)