Question for the woodworkers...
#32
I stripped the finish again from the patch and a little of the surrounding wood. Applied some two part bleach to the patch with a Q-tip and watched it slowly lighten in color until it looked liked the surrounding wood that had no stain on it. Neutralized the bleach and let it dry overnight, then touched up the area with a little stain the next day - followed by several coats of tung oil 24 hours apart.

Far from perfect, but close enough for government work.
Thanks again for the walnut piece Tom. You saved the day for me. Worthy

   
Willie
Reply
Thanks given by:


Messages In This Thread
Question for the woodworkers... - by Highpower - 09-27-2013, 05:16 PM
RE: Question for the woodworkers... - by TomG - 09-27-2013, 05:34 PM
RE: Question for the woodworkers... - by f350ca - 09-27-2013, 05:53 PM
RE: Question for the woodworkers... - by EdK - 09-27-2013, 06:20 PM
RE: Question for the woodworkers... - by TomG - 09-27-2013, 08:48 PM
RE: Question for the woodworkers... - by TomG - 10-10-2013, 12:26 PM
RE: Question for the woodworkers... - by EdK - 10-10-2013, 12:57 PM
RE: Question for the woodworkers... - by LJP - 10-10-2013, 12:57 PM
RE: Question for the woodworkers... - by TomG - 10-10-2013, 01:18 PM
RE: Question for the woodworkers... - by f350ca - 10-10-2013, 06:45 PM
RE: Question for the woodworkers... - by LJP - 10-10-2013, 10:30 PM
RE: Question for the woodworkers... - by TomG - 10-10-2013, 11:16 PM
RE: Question for the woodworkers... - by TomG - 10-11-2013, 03:56 PM
RE: Question for the woodworkers... - by stevec - 10-11-2013, 04:01 PM
RE: Question for the woodworkers... - by EdK - 10-11-2013, 04:03 PM
RE: Question for the woodworkers... - by TomG - 10-11-2013, 11:01 PM
RE: Question for the woodworkers... - by TomG - 10-14-2013, 11:06 PM
RE: Question for the woodworkers... - by oldgoaly - 10-14-2013, 11:09 PM
RE: Question for the woodworkers... - by LJP - 10-15-2013, 05:01 AM
RE: Question for the woodworkers... - by LJP - 10-15-2013, 10:25 AM
RE: Question for the woodworkers... - by TomG - 10-15-2013, 10:34 AM
RE: Question for the woodworkers... - by Highpower - 10-24-2013, 03:56 PM
RE: Question for the woodworkers... - by f350ca - 10-24-2013, 04:43 PM
RE: Question for the woodworkers... - by EdK - 10-24-2013, 05:09 PM
RE: Question for the woodworkers... - by TomG - 10-24-2013, 06:15 PM
RE: Question for the woodworkers... - by Mayhem - 10-24-2013, 07:04 PM
RE: Question for the woodworkers... - by LJP - 10-27-2013, 05:31 AM
RE: Question for the woodworkers... - by DaveH - 10-27-2013, 08:31 AM



Users browsing this thread: 2 Guest(s)