New Lathe
#3
Hi John,

How does the Harrison compare to your Boxford in size? Are you replacing the Boxford with the Harrison or adding it to your shop?
Nice score with all that tooling. Wise choice going with a Harrison. Mick is an expert on Harrison lathes, as we all know.

Ed
Reply
Thanks given by:


Messages In This Thread
New Lathe - by doubleboost - 02-22-2015, 12:27 PM
RE: New Lathe - by tekfab - 02-22-2015, 12:57 PM
RE: New Lathe - by EdK - 02-22-2015, 01:00 PM
RE: New Lathe - by mfletch - 02-22-2015, 01:23 PM
RE: New Lathe - by DaveH - 02-22-2015, 02:06 PM
RE: New Lathe - by Micktoon - 02-22-2015, 04:42 PM
RE: New Lathe - by doubleboost - 02-22-2015, 04:53 PM
RE: New Lathe - by mike-sid - 02-22-2015, 08:36 PM
RE: New Lathe - by krv3000 - 02-22-2015, 05:09 PM
RE: New Lathe - by Mayhem - 02-22-2015, 05:33 PM
RE: New Lathe - by Shawn - 02-22-2015, 11:09 PM
RE: New Lathe - by mike-sid - 02-22-2015, 11:19 PM
RE: New Lathe - by doubleboost - 02-23-2015, 06:29 PM
RE: New Lathe - by doubleboost - 02-23-2015, 06:29 PM
RE: New Lathe - by EdK - 02-23-2015, 06:39 PM
RE: New Lathe - by DaveH - 02-23-2015, 06:42 PM
RE: New Lathe - by Dr Stan - 02-23-2015, 06:53 PM
RE: New Lathe - by doubleboost - 02-28-2015, 02:54 PM
RE: New Lathe - by EdK - 02-28-2015, 02:58 PM
RE: New Lathe - by DaveH - 02-28-2015, 03:03 PM
RE: New Lathe - by Micktoon - 02-28-2015, 06:45 PM
RE: New Lathe - by f350ca - 02-28-2015, 08:44 PM
RE: New Lathe - by mike-sid - 02-28-2015, 09:03 PM
RE: New Lathe - by Highpower - 02-28-2015, 10:00 PM
RE: New Lathe - by trevatxtal - 03-01-2015, 03:29 AM
RE: New Lathe - by tekfab - 03-01-2015, 05:07 AM
RE: New Lathe - by Shawn - 03-01-2015, 06:07 AM
RE: New Lathe - by PixMan - 03-01-2015, 08:19 AM
RE: New Lathe - by mike-sid - 03-01-2015, 11:45 PM
RE: New Lathe - by doubleboost - 04-04-2015, 02:32 PM
RE: New Lathe - by DaveH - 04-04-2015, 03:44 PM
RE: New Lathe - by mike-sid - 04-04-2015, 05:34 PM
RE: New Lathe - by f350ca - 04-04-2015, 07:17 PM
RE: New Lathe - by Mayhem - 04-04-2015, 07:19 PM
RE: New Lathe - by EdK - 04-04-2015, 08:56 PM
RE: New Lathe - by Mayhem - 04-05-2015, 12:09 AM
RE: New Lathe - by PixMan - 04-05-2015, 09:37 PM
RE: New Lathe - by DaveH - 04-06-2015, 10:47 AM
RE: New Lathe - by krv3000 - 04-05-2015, 05:44 PM



Users browsing this thread: 2 Guest(s)