More lathe gadgets
#19
Here it is.  I still need to find a magnet around here.  I have plenty of hard drive magnets but they're still in the hard drives.   I also need to add a bit more plastic to the bottom, it's a bit thin in the middle as you can see. It measures 1.125" x 0.750" and the little hole in the side has a 6-32 set screw in it holding on to the DI.  I did it that way 'cuze I have a DTI that's smaller in diameter and the tab on the back is smaller than these.

Thinking about it now, what I should've done was just made a plastic cylinder and milled the hole for the DI tab afterward.

Seeing how it came out, I'm going to make a mold of it so I can make more.  

[Image: block.jpg]
Reply
Thanks given by:


Messages In This Thread
More lathe gadgets - by Micktoon - 03-01-2015, 05:54 PM
RE: More lathe gadgets - by doubleboost - 03-01-2015, 06:13 PM
RE: More lathe gadgets - by stevec - 03-01-2015, 08:24 PM
RE: More lathe gadgets - by Highpower - 03-02-2015, 01:17 PM
RE: More lathe gadgets - by Mayhem - 03-04-2015, 01:52 AM
RE: More lathe gadgets - by f350ca - 03-01-2015, 09:01 PM
RE: More lathe gadgets - by stevec - 03-02-2015, 07:56 AM
RE: More lathe gadgets - by Micktoon - 03-02-2015, 04:13 PM
RE: More lathe gadgets - by krv3000 - 03-02-2015, 05:09 PM
RE: More lathe gadgets - by Roadracer_Al - 03-02-2015, 06:54 PM
RE: More lathe gadgets - by Dr Stan - 03-03-2015, 10:55 AM
RE: More lathe gadgets - by Micktoon - 03-04-2015, 03:33 AM
RE: More lathe gadgets - by Mayhem - 03-04-2015, 03:39 AM
RE: More lathe gadgets - by awemawson - 03-04-2015, 06:33 AM
RE: More lathe gadgets - by f350ca - 03-04-2015, 09:44 AM
RE: More lathe gadgets - by Vinny - 03-04-2015, 05:24 PM
RE: More lathe gadgets - by Micktoon - 03-04-2015, 05:46 PM
RE: More lathe gadgets - by Vinny - 03-04-2015, 06:01 PM
RE: More lathe gadgets - by Vinny - 03-05-2015, 07:56 PM
RE: More lathe gadgets - by Micktoon - 03-06-2015, 03:37 AM
RE: More lathe gadgets - by Vinny - 03-10-2015, 04:48 PM
RE: More lathe gadgets - by Highpower - 03-11-2015, 11:16 AM
RE: More lathe gadgets - by Vinny - 03-11-2015, 11:45 AM
RE: More lathe gadgets - by DaveH - 03-11-2015, 12:01 PM
RE: More lathe gadgets - by Highpower - 03-11-2015, 12:09 PM
RE: More lathe gadgets - by EdK - 03-11-2015, 04:35 PM
RE: More lathe gadgets - by Highpower - 03-12-2015, 01:11 AM
RE: More lathe gadgets - by Mayhem - 03-11-2015, 10:27 PM
RE: More lathe gadgets - by EdK - 03-12-2015, 06:12 AM
RE: More lathe gadgets - by Vinny - 03-12-2015, 03:59 PM
RE: More lathe gadgets - by dallen - 03-12-2015, 04:57 PM
RE: More lathe gadgets - by Highpower - 03-12-2015, 09:30 PM
RE: More lathe gadgets - by EdK - 03-12-2015, 05:04 PM
RE: More lathe gadgets - by Vinny - 03-12-2015, 05:07 PM
RE: More lathe gadgets - by Micktoon - 03-16-2015, 07:18 PM
RE: More lathe gadgets - by f350ca - 03-16-2015, 07:34 PM
RE: More lathe gadgets - by PixMan - 03-16-2015, 08:40 PM



Users browsing this thread: 1 Guest(s)