MetalworkingFun Forum › Machining › General Metalworking Discussion v
What face mill do u use???

Thread Modes
What face mill do u use???
DaveH Offline
Child of the 60's
******
Posts: 4,513
Threads: 139
Joined: Feb 2012
Location: Kempton Park. South Africa
The following 2 users Like DaveH's post:
PixMan (03-20-2015), EdK (03-20-2015)
#58
03-20-2015, 02:56 PM
aRM,
Measuring the feed rate is very easy. Mark the mill table using a crayon two lines say 500 or 750 mm apart. Run the X axis feed you don't have to run the spindle and use a stop watch to measure the time between the two lines. Now you didn't think it was that easy did you Smile 

Use the measured feed to calibrate your (speed) control knob. The knob you turn to increase decrease the feed has some numbers next to it.

Easy Smile 

Smiley-eatdrink004 
DaveH
Reply
Thanks given by:


Messages In This Thread
What face mill do u use??? - by aRM - 03-08-2015, 04:03 PM
RE: WHAT FACEMILL DO U USE ??? - by EdK - 03-08-2015, 04:18 PM
RE: WHAT FACEMILL DO U USE ??? - by aRM - 03-08-2015, 04:45 PM
RE: WHAT FACEMILL DO U USE ??? - by stevec - 03-08-2015, 05:20 PM
RE: WHAT FACEMILL DO U USE ??? - by PixMan - 03-08-2015, 06:26 PM
RE: What face mill do u use??? - by stevec - 03-08-2015, 06:51 PM
RE: What face mill do u use??? - by PixMan - 03-08-2015, 06:59 PM
RE: What face mill do u use??? - by stevec - 03-08-2015, 07:11 PM
RE: What face mill do u use??? - by PixMan - 03-08-2015, 07:21 PM
RE: What face mill do u use??? - by mike-sid - 03-08-2015, 08:21 PM
RE: What face mill do u use??? - by Highpower - 03-08-2015, 08:32 PM
RE: What face mill do u use??? - by PixMan - 03-08-2015, 09:52 PM
RE: What face mill do u use??? - by mike-sid - 03-08-2015, 10:21 PM
RE: What face mill do u use??? - by Highpower - 03-08-2015, 11:47 PM
RE: What face mill do u use??? - by PixMan - 03-08-2015, 10:32 PM
RE: What face mill do u use??? - by PixMan - 03-09-2015, 06:46 AM
RE: What face mill do u use??? - by Highpower - 03-09-2015, 10:06 AM
RE: What face mill do u use??? - by DaveH - 03-09-2015, 11:31 AM
RE: What face mill do u use??? - by EdK - 03-09-2015, 12:02 PM
RE: What face mill do u use??? - by DaveH - 03-09-2015, 12:19 PM
RE: What face mill do u use??? - by EdK - 03-09-2015, 12:26 PM
RE: What face mill do u use??? - by aRM - 03-09-2015, 12:40 PM
RE: What face mill do u use??? - by DaveH - 03-09-2015, 12:42 PM
RE: What face mill do u use??? - by aRM - 03-09-2015, 12:48 PM
RE: What face mill do u use??? - by DaveH - 03-09-2015, 12:56 PM
RE: What face mill do u use??? - by DaveH - 03-09-2015, 12:52 PM
RE: What face mill do u use??? - by aRM - 03-09-2015, 01:36 PM
RE: What face mill do u use??? - by PixMan - 03-09-2015, 01:53 PM
RE: What face mill do u use??? - by aRM - 03-09-2015, 02:32 PM
RE: What face mill do u use??? - by DaveH - 03-09-2015, 01:56 PM
RE: What face mill do u use??? - by aRM - 03-09-2015, 02:53 PM
RE: What face mill do u use??? - by PixMan - 03-09-2015, 10:55 PM
RE: What face mill do u use??? - by aRM - 03-10-2015, 12:30 AM
RE: What face mill do u use??? - by aRM - 03-13-2015, 02:33 PM
RE: What face mill do u use??? - by PixMan - 03-09-2015, 06:07 PM
RE: What face mill do u use??? - by aRM - 03-10-2015, 12:05 AM
RE: What face mill do u use??? - by Mayhem - 03-10-2015, 05:44 AM
RE: What face mill do u use??? - by PixMan - 03-10-2015, 07:45 AM
RE: What face mill do u use??? - by aRM - 03-11-2015, 12:47 PM
RE: What face mill do u use??? - by PixMan - 03-11-2015, 04:22 PM
RE: What face mill do u use??? - by aRM - 03-13-2015, 03:24 PM
RE: What face mill do u use??? - by PixMan - 03-11-2015, 09:27 PM
RE: What face mill do u use??? - by DaveH - 03-13-2015, 03:50 PM
RE: What face mill do u use??? - by PixMan - 03-13-2015, 07:22 PM
RE: What face mill do u use??? - by aRM - 03-18-2015, 02:59 PM
RE: What face mill do u use??? - by DaveH - 03-18-2015, 03:16 PM
RE: What face mill do u use??? - by aRM - 03-19-2015, 01:31 PM
RE: What face mill do u use??? - by DaveH - 03-18-2015, 03:49 PM
RE: What face mill do u use??? - by aRM - 03-19-2015, 01:43 PM
RE: What face mill do u use??? - by Vinny - 03-18-2015, 04:45 PM
RE: What face mill do u use??? - by DaveH - 03-18-2015, 05:15 PM
RE: What face mill do u use??? - by PixMan - 03-18-2015, 05:41 PM
RE: What face mill do u use??? - by aRM - 03-19-2015, 02:01 PM
RE: What face mill do u use??? - by DaveH - 03-19-2015, 03:24 PM
RE: What face mill do u use??? - by aRM - 03-20-2015, 02:19 PM
RE: What face mill do u use??? - by PixMan - 03-19-2015, 07:02 PM
RE: What face mill do u use??? - by aRM - 03-20-2015, 02:33 PM
RE: What face mill do u use??? - by DaveH - 03-20-2015, 02:56 PM
RE: What face mill do u use??? - by aRM - 03-22-2015, 12:00 PM
RE: What face mill do u use??? - by PixMan - 03-20-2015, 04:28 PM
RE: What face mill do u use??? - by aRM - 03-22-2015, 12:31 PM
RE: What face mill do u use??? - by DaveH - 03-22-2015, 01:36 PM
RE: What face mill do u use??? - by aRM - 03-24-2015, 12:12 AM
RE: What face mill do u use??? - by Mayhem - 03-24-2015, 05:49 AM
RE: What face mill do u use??? - by aRM - 03-24-2015, 01:49 PM
RE: What face mill do u use??? - by PixMan - 03-22-2015, 01:46 PM
RE: What face mill do u use??? - by aRM - 03-24-2015, 02:28 PM
RE: What face mill do u use??? - by PixMan - 03-22-2015, 02:08 PM
RE: What face mill do u use??? - by aRM - 03-24-2015, 12:21 AM
RE: What face mill do u use??? - by PixMan - 03-24-2015, 10:38 PM
RE: What face mill do u use??? - by aRM - 03-25-2015, 12:07 AM



Users browsing this thread: 1 Guest(s)