ER32 Collet Chuck for Proxxon PD 400
#89
Lolz... Thanks Rob. Taken that pic from the company's intranet.

I'm thinking of deepening the counterbores a little more so that I can square off the flange. Do you folks think its necessary? Also, the bolts I bought are too long. Tried holding them on the chuck with some nuts. Kept running back. If I'm to Loctite them onto the nuts and later apply heat to remove, will the leftover Loctite fouled the cap screws? Otherwise, I'll go get shorter M6 cap screws when I'm back.

Regards,
Wong
Wongster
http://www.wongstersproduction.com

Proud to be a member of MetalworkingFun Forum since Mar 2012.
Reply
Thanks given by:


Messages In This Thread
RE: ER32 Collet Chuck for Proxxon PD 400 - by EdK - 04-15-2012, 06:35 PM
RE: ER32 Collet Chuck for Proxxon PD 400 - by RobWilson - 04-16-2012, 09:29 AM
RE: ER32 Collet Chuck for Proxxon PD 400 - by RobWilson - 04-16-2012, 10:13 AM
RE: ER32 Collet Chuck for Proxxon PD 400 - by RobWilson - 04-16-2012, 11:11 AM
RE: ER32 Collet Chuck for Proxxon PD 400 - by EdK - 04-16-2012, 12:36 PM
RE: ER32 Collet Chuck for Proxxon PD 400 - by EdK - 05-01-2012, 09:06 AM
RE: ER32 Collet Chuck for Proxxon PD 400 - by EdK - 05-01-2012, 11:23 AM
RE: ER32 Collet Chuck for Proxxon PD 400 - by EdK - 05-01-2012, 12:22 PM
RE: ER32 Collet Chuck for Proxxon PD 400 - by EdK - 05-07-2012, 06:20 PM
RE: ER32 Collet Chuck for Proxxon PD 400 - by RobWilson - 05-19-2012, 04:23 AM
RE: ER32 Collet Chuck for Proxxon PD 400 - by RobWilson - 05-20-2012, 04:37 AM
RE: ER32 Collet Chuck for Proxxon PD 400 - by RobWilson - 05-20-2012, 01:07 PM
RE: ER32 Collet Chuck for Proxxon PD 400 - by EdK - 05-20-2012, 01:23 PM
RE: ER32 Collet Chuck for Proxxon PD 400 - by RobWilson - 05-20-2012, 01:40 PM
RE: ER32 Collet Chuck for Proxxon PD 400 - by EdK - 05-20-2012, 03:25 PM
RE: ER32 Collet Chuck for Proxxon PD 400 - by RobWilson - 05-31-2012, 04:26 PM
RE: ER32 Collet Chuck for Proxxon PD 400 - by Wongster - 05-31-2012, 06:22 PM
RE: ER32 Collet Chuck for Proxxon PD 400 - by RobWilson - 06-01-2012, 02:40 AM
RE: ER32 Collet Chuck for Proxxon PD 400 - by EdK - 06-20-2012, 08:06 PM
RE: ER32 Collet Chuck for Proxxon PD 400 - by EdK - 06-25-2012, 03:14 PM



Users browsing this thread: 2 Guest(s)