MetalworkingFun Forum › Machining › General Metalworking Discussion v
Broken tiny tap in aluminium

Thread Modes
Broken tiny tap in aluminium
Vinny Offline
Another Whipping Boy
*******
Posts: 2,597
Threads: 99
Joined: Dec 2014
Location: Michigan
The following 2 users Like Vinny's post:
f350ca (09-08-2016), EdK (09-08-2016)
#11
09-08-2016, 06:49 PM
(09-08-2016, 12:51 PM)flosi Wrote: Alcohol, any kind, is also good for cutting al. Leaves no residue and is less hazardous than than thinner.

Wow, so beer is good for cutting aluminum? Oh wait... I might have already known that.
Logan 200, Index 40H Mill, Boyer-Shultz 612 Surface Grinder, HF 4x6 Bandsaw, a shear with no name, ...
the nobucks boutique etsy shop  |  the nobucks boutique
Website
Reply
Thanks given by:


Messages In This Thread
Broken tiny tap in aluminium - by Wongster - 09-07-2016, 11:00 AM
RE: Broken tiny tap in aluminium - by NormanV - 09-07-2016, 12:28 PM
RE: Broken tiny tap in aluminium - by Dr Stan - 09-07-2016, 02:58 PM
RE: Broken tiny tap in aluminium - by TomG - 09-07-2016, 08:42 PM
RE: Broken tiny tap in aluminium - by Vinny - 09-07-2016, 09:31 PM
RE: Broken tiny tap in aluminium - by Mike E. - 09-08-2016, 04:40 AM
RE: Broken tiny tap in aluminium - by Dr Stan - 09-08-2016, 06:40 PM
RE: Broken tiny tap in aluminium - by Highpower - 09-08-2016, 12:22 PM
RE: Broken tiny tap in aluminium - by flosi - 09-08-2016, 12:51 PM
RE: Broken tiny tap in aluminium - by Vinny - 09-08-2016, 06:49 PM
RE: Broken tiny tap in aluminium - by Dr Stan - 09-08-2016, 09:57 PM
RE: Broken tiny tap in aluminium - by flosi - 09-09-2016, 03:07 PM
RE: Broken tiny tap in aluminium - by oldskoolron - 09-09-2016, 01:47 AM
RE: Broken tiny tap in aluminium - by johnnyc14 - 09-09-2016, 12:15 PM
RE: Broken tiny tap in aluminium - by TomG - 09-09-2016, 04:24 PM
RE: Broken tiny tap in aluminium - by Dr Stan - 09-10-2016, 12:21 PM
RE: Broken tiny tap in aluminium - by flosi - 09-13-2016, 03:16 PM
RE: Broken tiny tap in aluminium - by Wongster - 09-14-2016, 07:04 PM
RE: Broken tiny tap in aluminium - by Highpower - 09-15-2016, 06:05 AM
RE: Broken tiny tap in aluminium - by Highpower - 09-15-2016, 03:54 PM
RE: Broken tiny tap in aluminium - by Vinny - 09-15-2016, 06:28 PM
RE: Broken tiny tap in aluminium - by Highpower - 09-15-2016, 10:29 PM
RE: Broken tiny tap in aluminium - by Vinny - 09-15-2016, 10:39 PM
RE: Broken tiny tap in aluminium - by Highpower - 09-15-2016, 11:16 PM
RE: Broken tiny tap in aluminium - by Vinny - 09-16-2016, 04:15 PM



Users browsing this thread: 1 Guest(s)