6" Fortis/Clausing lathe

Hello There, Guest! Register

Thread Modes

Help 6" Fortis/Clausing lathe

Seanlogie Offline

Offline

Freshman

Posts: 17
Threads: 3
Joined: Dec 2016
Location: Scotland

The following 1 user Likes Seanlogie's post:
flosi (12-12-2016)

#21

12-10-2016, 01:47 AM

This is my setup on the Fortis as is,excuse my ignorance but where does the 127 tooth go .

THanks gor all the replies it's be great . Thumbsup

Thumbsup

Attached Files Thumbnail(s)

Reply

« Next Oldest | Next Newest »

Messages In This Thread

6" Fortis/Clausing lathe - by Seanlogie - 12-04-2016, 02:57 AM

RE: 6" Fortis/Clausing lathe - by Vinny - 12-04-2016, 03:08 AM

RE: 6" Fortis/Clausing lathe - by Seanlogie - 12-05-2016, 02:37 AM

RE: 6" Fortis/Clausing lathe - by Pete O - 12-04-2016, 05:15 AM

RE: 6" Fortis/Clausing lathe - by Seanlogie - 12-05-2016, 02:34 AM

RE: 6" Fortis/Clausing lathe - by Mayhem - 12-05-2016, 08:25 AM

RE: 6" Fortis/Clausing lathe - by Seanlogie - 12-05-2016, 01:22 PM

RE: 6" Fortis/Clausing lathe - by Dr Stan - 12-05-2016, 02:17 PM

RE: 6" Fortis/Clausing lathe - by EdK - 12-05-2016, 05:16 PM

RE: 6" Fortis/Clausing lathe - by Seanlogie - 12-06-2016, 05:39 AM

RE: 6" Fortis/Clausing lathe - by Seanlogie - 12-06-2016, 06:18 AM

RE: 6" Fortis/Clausing lathe - by Mayhem - 12-06-2016, 06:30 AM

RE: 6" Fortis/Clausing lathe - by Seanlogie - 12-06-2016, 08:32 AM

RE: 6" Fortis/Clausing lathe - by Seanlogie - 12-09-2016, 09:54 AM

RE: 6" Fortis/Clausing lathe - by Dr Stan - 12-09-2016, 10:23 AM

RE: 6" Fortis/Clausing lathe - by Seanlogie - 12-09-2016, 02:21 PM

RE: 6" Fortis/Clausing lathe - by EdK - 12-09-2016, 04:40 PM

RE: 6" Fortis/Clausing lathe - by Vinny - 12-09-2016, 07:36 PM

RE: 6" Fortis/Clausing lathe - by Mayhem - 12-09-2016, 08:26 PM

RE: 6" Fortis/Clausing lathe - by Vinny - 12-09-2016, 08:42 PM

RE: 6" Fortis/Clausing lathe - by Dr Stan - 12-10-2016, 01:54 AM

RE: 6" Fortis/Clausing lathe - by Seanlogie - 12-10-2016, 01:47 AM

RE: 6" Fortis/Clausing lathe - by Pete O - 12-10-2016, 02:18 AM

RE: 6" Fortis/Clausing lathe - by Seanlogie - 12-10-2016, 02:50 AM

RE: 6" Fortis/Clausing lathe - by Seanlogie - 12-13-2016, 01:34 PM

Users browsing this thread: 1 Guest(s)