Precision Matthews PM-728V-T Mill
#19
(09-10-2022, 11:37 AM)EdK Wrote: Unfortunately it's not solid, it's hollow on the back side. It has hollow slots on the back side of the rim so I can cut some metal and glue it inside the slots.

Ed

Oh for Pete's sake! No wonder the weight of the handle is dragging it around.  Slaphead
Got a spare 12ga. bird-shot shell handy?  Big Grin
Take the handle off and weigh it. Open up the shell and weigh out the same amount of lead shot. Dump it in the slots and cover with hot glue or epoxy. Bob's your uncle. That is how I adjusted the balance point on my competition rifles. Lead shot inside the butt stocks. Works a treat.
Willie
Reply
Thanks given by:


Messages In This Thread
Precision Matthews PM-728V-T Mill - by EdK - 04-19-2022, 01:14 PM
RE: Precision Matthews PM-728V-T Mill - by EdK - 04-20-2022, 08:11 PM
RE: Precision Matthews PM-728V-T Mill - by Vinny - 04-21-2022, 01:51 PM
RE: Precision Matthews PM-728V-T Mill - by EdK - 04-21-2022, 04:37 PM
RE: Precision Matthews PM-728V-T Mill - by rleete - 04-22-2022, 10:18 AM
RE: Precision Matthews PM-728V-T Mill - by EdK - 04-22-2022, 10:50 AM
RE: Precision Matthews PM-728V-T Mill - by EdK - 04-22-2022, 05:56 PM
RE: Precision Matthews PM-728V-T Mill - by EdK - 04-22-2022, 06:44 PM
RE: Precision Matthews PM-728V-T Mill - by EdK - 05-01-2022, 07:02 PM
RE: Precision Matthews PM-728V-T Mill - by EdK - 05-02-2022, 11:29 PM
RE: Precision Matthews PM-728V-T Mill - by EdK - 05-03-2022, 07:49 PM
RE: Precision Matthews PM-728V-T Mill - by EdK - 05-04-2022, 07:35 PM
RE: Precision Matthews PM-728V-T Mill - by EdK - 09-09-2022, 07:41 PM
RE: Precision Matthews PM-728V-T Mill - by EdK - 09-10-2022, 11:37 AM
RE: Precision Matthews PM-728V-T Mill - by Highpower - 09-10-2022, 12:42 PM
RE: Precision Matthews PM-728V-T Mill - by EdK - 09-10-2022, 03:48 PM
RE: Precision Matthews PM-728V-T Mill - by rleete - 09-10-2022, 05:21 PM
RE: Precision Matthews PM-728V-T Mill - by EdK - 09-10-2022, 06:37 PM
RE: Precision Matthews PM-728V-T Mill - by EdK - 09-11-2022, 11:10 AM
RE: Precision Matthews PM-728V-T Mill - by rleete - 09-11-2022, 07:14 PM
RE: Precision Matthews PM-728V-T Mill - by EdK - 09-11-2022, 08:44 PM
RE: Precision Matthews PM-728V-T Mill - by EdK - 09-12-2022, 10:27 AM
RE: Precision Matthews PM-728V-T Mill - by EdK - 09-12-2022, 01:28 PM
RE: Precision Matthews PM-728V-T Mill - by EdK - 09-12-2022, 05:26 PM
RE: Precision Matthews PM-728V-T Mill - by EdK - 09-13-2022, 07:17 PM
RE: Precision Matthews PM-728V-T Mill - by EdK - 09-12-2022, 05:26 PM
RE: Precision Matthews PM-728V-T Mill - by rleete - 09-12-2022, 04:19 PM
RE: Precision Matthews PM-728V-T Mill - by EdK - 09-12-2022, 05:27 PM



Users browsing this thread: 1 Guest(s)